MXA-32 ADSL IP DSLAM

[aspid]

Добрый день!
Помогите разобраться
После сброса настроек к заводским на дслма возникла следующая проблема, дслам перезагружается
Net:
device MXA, host MXA
88e6131: ID 0x141 success!
SFP1 Up
SFP2 Up
IP: 192.168.2.40
Server IP: 192.168.0.70
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Feb 10 2010 02:24:16
***************************************
### main_loop: bootcmd="run nfsboot"
Hit any key to stop autoboot: 0
Using device
TFTP from server 192.168.0.70; our IP address is 192.168.2.40; sending through g
ateway 192.168.0.1
Filename 'uImage'.
Load address: 0x80a00000
Loading: T1 T1 T1 T1 T1 T1 T1 T1 T1 T1
Retry count exceeded; starting again

Can't load from network
Load from FLASH, altbootcmd="cp.b c0420000 80a00000 780000;bootm 80a00000"


Copy 7864320 bytes .............................................................


## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 5568635 Bytes = 5.3 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Comandline = flashboot
Reset FE tx bd index to zero ... Starting kernel at 0x801006d8 ...


LINUX started...
DETECTED system memsize: 67108864 bytes.
2Boot:[2]flashboot
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
Linux version 2.4.20-MVS (root@linux) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-
9))
#188 Tue Aug 17 09:31:22 NOVST 2010
Can't analyze prologue code at 8011ec18
Determined physical RAM map:
Initial ramdisk at: 0x80279000 (5013504 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,57600
trap_init:board_be_init blocked
r4koff 1000000 CPU 200.00 MHz
Console: colour dummy device 80x25
Enable Watchdog driver
0.81 BogoMIPS
MIPS CPU counter frequency is fixed at 100000000 Hz
Memory: 57232k/57952k available (1296k kernel code, 720k reserved, 5000k data, 8
4k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware on host bus 0.Ignored
Initialize Diplomat-IP Fast Ethernet device.
Request IO region for FE Ethernet device, name=eth0.
eth0: TXC-FE ether at 0x280, using assigned IRQ 6
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
initialize_kbd: Keyboard failed self test
malta_int.c:the irq 1 is invalid
Serial driver version 5.05c (2001-
07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI S
ERIAL_Diplomat-IP enabled
ttyS00 at 0x03f8 (irq = 3) is a ST16654
RAMDISK driver initialized: 1 RAM disks of 25000K size 1024 blocksize
loop: loaded (max 8 devices)
pld: version mxa32_v7.c Aug 17 2010 09:31:50
pld: image 78422 bytes, reset nCONFIG... ok, set nCONFIG... ok
loading: ....................OK
init spi(twi) devices:
at26df321 device
physmap flash device: 2000000 at 1fc00000
gl256: Found 1 x16 devices at 0x0 in 16-bit mode
num 1 mrf 1 id 227e
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Enabling fast programming.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cryptoapi: loaded
cryptoapi: Registered md5 (0)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4896k freed
cnanda: make device for BOOT DISK.
cnanda: mount root file system...
VFS: Mounted root (ext2 filesystem).
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.7.2 (2010-04-16 10:13:30 MDT)
enter minte module
apply network from user config
ifconfig: eth0 mac 02:00:00:02:02:22 ip 172.16.201.8
netmask 255.255.255.240 gw 172.16.201.1 up
vconfig : eth0.2 up
eth0.2: add 01:00:5e:00:00:01 mcast address to master interface
apply configs name from user config
## Error: "loadfw" not defined
## Error: "devicemodel" not defined
>> decompress binary
mv: cannot rename '/mnt/.tgz': No such file or directory
tar: can't open '.tgz': No such file or directory
mv: cannot rename '/wlog': No such file or directory
mv: cannot rename '/dfl': No such file or directory
mv: cannot rename '/cli': No such file or directory
mv: cannot rename '/enpu': No such file or directory
mv: cannot rename '/adsl': No such file or directory
mv: cannot rename '/mswi': No such file or directory
mv: cannot rename '/gbase': No such file or directory
mv: cannot rename '/webs': No such file or directory
mv: cannot rename '/snmpd': No such file or directory
chmod: /bin/wlog: No such file or directory
chmod: /bin/cli: No such file or directory
chmod: /mnt/work/enpu: No such file or directory
chmod: /mnt/work/adsl: No such file or directory
chmod: /mnt/work/mswi: No such file or directory
chmod: /mnt/work/gbase: No such file or directory
chmod: /mnt/work/webs: No such file or directory
chmod: /mnt/work/snmpd: No such file or directory
tar: can't open 'web.tgz': No such file or directory
>> copy security
Can't find 'id=8' on flash
Can't find 'id=7' on flash
Can't find 'id=9' on flash
/mnt/work/webs: not found
/bin/wlog: not found
/mnt/work/gbase: not found
/mnt/work/adsl: not found
/mnt/work/mswi: not found
/mnt/work/enpu: not found
/mnt/work/snmpd: not found
/bin/cli: not found
reboot device due to ...
The system is going down NOW!
Sending SIGTERM to all processes
Sending SIGKILL to all processes

Requesting system reboot
Restarting system.

[Кирилл]

Здравствуйте!
1.Остановите загрузку нажатием любой клавиши в момент
Hit any key to stop autoboot: 0 (когда идет отсчет).
2.Залогинтесь к устройству root/admin
3.введите команду print и все, что выведет пришлите сюда, либо в почту kirill@eltex.org

[aspid]

Здравствуйте!
1.Остановите загрузку нажатием любой клавиши в момент
Hit any key to stop autoboot: 0 (когда идет отсчет).
2.Залогинтесь к устройству root/admin
3.введите команду print и все, что выведет пришлите сюда, либо в почту kirill@eltex.org

Вот что выдал
@>print
bootcmd=run nfsboot
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
ethaddr=10:11:12:40:2:40
ipaddr=192.168.2.40
serverip=192.168.0.70
preboot=
ethact=
krnload=tftp 80a00000 $(kernfile)
fwchange1=tftp 80a00000 $(kernfile);erase bfc60000 c03dffff;cp.b 80a00000 bfc600
00 780000
fwchange2=tftp 80a00000 $(kernfile);erase c0420000 c0b9ffff;cp.b 80a00000 c04200
00 780000
ubchange=tftp 80a00000 u-boot.bin;protect off bfc00000 bfc3ffff;erase bfc00000 b
fc3ffff;cp.b 80a00000 bfc00000 34000
altbootcmd=cp.b c0420000 80a00000 780000;bootm 80a00000
kernfile=uImage
gatewayip=192.168.0.1
netmask=255.255.255.0
hostname=MXA
sysname=MXA
netretry=no

Environment size: 663/131068 bytes

[Кирилл]

В этом же меню необходимо внести переменные (по какой-то причине они слетели)
set devicemodel mxa32
set loadfw no
set bootcmd run krnload\;bootm 80a00000
set nfsboot
save


После всех этих команд reset и смотрим загрузку

[aspid]

В этом же меню необходимо внести переменные (по какой-то причине они слетели)
set devicemodel mxa32
set loadfw no
set bootcmd run krnload\;bootm 80a00000
set nfsboot
save


После всех этих команд reset и смотрим загрузку

Спасибо ! Все заработало

[Кирилл]

Хорошо