mxa-24. Не загружается

[Батор]

Здравствуйте! Проблема с мха-24.Не загружается.
@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
preboot=
ethact=
fwchange=run krnload; run fwerase; run krnflash;
krnload=tftp 80a00000 $(kernfile)
fwerase=erase bfc60000 c017ffff
krnflash=cp.b 80a00000 bfc60000 500000
ubchange=run ubload; run ubunprot; run uberase; run ubflash
ubunprot=protect off bfc00000 bfc3ffff
uberase=erase bfc00000 bfc3ffff
ubflash=cp.b 80a00000 bfc00000 34000
altbootcmd=run loadfkern;bootm 80a00000
loadfkern=cp.b bfc60000 80a00000 500000
flash_boot_name=u-boot.bin
vinterface=on
hostname=MXA
devicemodel=mxa24
mtu=1400
dslfile=dslam_v2.1.bin
webfile=webs_v2.1
webpgfile=web_v2.1
clifile=cli
sysname=MXA
ldrfile=u-boot.bin
ubload=tftp 80a00000 u-boot.bin
ethaddr=02:00:06:00:01:8a
mask=255.255.255.128
gate=172.16.25.1
dslcfgfile=dslam.cfg
snmpfile=snmpd_v2.1
snmpcfgfile=snmpd_v2.1.conf
kernfile=uImage_ip
timetowait=20
serverip=172.16.25.19
getewayip=10.131.19.249
vlan=999
ipaddr=172.16.25.88
gatewayip=172.16.25.1
netmask=255.255.255.128
bootcmd=run krnload;bootm 80a00000
netretry=no

Environment size: 1044/131068 bytes
@>

[Кирилл]

Здравствуйте.
Запустите мха так, чтобы он стянул прошраммное обеспечение с tftp сервера, после этого прошейте в память устройства все задачи и ядро.
После прошивки отключите tftp сервер и проверьте загружается ли МХА.

[Кирилл]

Уже была подобная тема viewtopic.php?f=2&t=2661

[Батор]

Здравствуйте. Не получается загрузить ПО. МХА с аналогичной проблемой. Пинги со стороны сервера не проходят.
Лог загрузки
U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Jun 23 2009 - 16:03:10)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1a1a0c20
Top of RAM usable for U-Boot at: 84000000
Reserving 452k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
-> DDR test:
................................
................................................
.................................................
.................................................
-> DDR test success!
SP at 0x83ecbf98 addr at 0x83f8c000
Relocate U-boot ...
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device MXA, host Altsag_M{A-24
88e6131: ID 0x141 success!
IP: 10.131.19.250
Server IP: 10.131.19.252
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Oct 15 2009 10:46:18
***************************************
### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0
*** ERROR: `ethaddr' not set
## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 4331564 Bytes = 4.1 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Comandline = flashboot
Reset FE tx bd index to zero ... Starting kernel at 0x801006d8 ...


LINUX started...
DETECTED system memsize: 67108864 bytes.
2Boot param = flashboot
Boot method = 2
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
Linux version 2.4.20-MVS (root@linuxsrv) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3
.3-9))
#110 Wed Nov 25 09:56:10 GMT+6 2009
Can't analyze prologue code at 8011eb38
Determined physical RAM map:
Initial ramdisk at: 0x8035f000 (3493888 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,57600
trap_init:board_be_init blocked
r4koff 1000000 CPU 200.00 MHz
Console: colour dummy device 80x25
0.81 BogoMIPS
MIPS CPU counter frequency is fixed at 100000000 Hz
Memory: 57792k/58512k available (1476k kernel code, 720k reserved, 4260k data, 8
4k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware on host bus 0.Ignored
Initialize Diplomat-IP Fast Ethernet device.
Request IO region for FE Ethernet device, name=eth0.
eth0: TXC-FE ether at 0x280, using assigned IRQ 6
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
initialize_kbd: Keyboard failed self test
malta_int.c:the irq 1 is invalid
Serial driver version 5.05c
(2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI
SERIAL_Diplomat-IP enabled
ttyS00 at 0x03f8 (irq = 3) is a ST16654
RAMDISK driver initialized: 1 RAM disks of 25000K size 1024 blocksize
loop: loaded (max 8 devices)
pld: version mxa{12-60}1v6.c Nov 25 2009 09:56:37
pld: image 78422 bytes, reset nCONFIG... ok, set nCONFIG... ok
loading: ....................OK
dsp: register device Nov 25 2009 09:56:41
init spi(twi) devices
b_wdg0, b_wdg1, b_wdg2, b_wdg: active
physmap flash device: 1000000 at 1fc00000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit mode
num 1 mrf 1 id 227e
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cryptoapi: loaded
cryptoapi: Registered md5 (0)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 3412k freed
cnanda: make device for BOOT DISK.
cnanda: mount root file system...
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.7.2 (2009-11-23 17:39:46 GMT+6)
enter minte module
## Error: "ethaddr" not defined
## Error: "vlan_res" not defined
## Error: "ipaddr_res" not defined
## Error: "netmask_res" not defined
error: can't get ethernet address!!!

@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
preboot=
ethact=
fwchange=run krnload; run fwerase; run krnflash;
krnload=tftp 80a00000 $(kernfile)
fwerase=erase bfc60000 c017ffff
krnflash=cp.b 80a00000 bfc60000 500000
ubchange=run ubload; run ubunprot; run uberase; run ubflash
ubunprot=protect off bfc00000 bfc3ffff
uberase=erase bfc00000 bfc3ffff
ubflash=cp.b 80a00000 bfc00000 34000
altbootcmd=run loadfkern;bootm 80a00000
loadfkern=cp.b bfc60000 80a00000 500000
flash_boot_name=u-boot.bin
vinterface=on
devicemodel=mxa24
mtu=1400
dslfile=dslam_v2.1.bin
webfile=webs_v2.1
webpgfile=web_v2.1
clifile=cli
sysname=MXA
ldrfile=u-boot_ip.bin
ubload=tftp 80a00000 u-boot_ip.bin
hostname=Altsag_M{A-24
netmask=255.255.255.248
ipaddr=10.131.19.250
gatewayip=10.131.19.249
dslcfgfile=dslam.cfg
snmpfile=snmpd_v2.1
snmpcfgfile=snmpd_v2.1.conf
kernfile=uImage_ip
serverip=10.131.19.252
vlan=5
bootcmd=run krnload;bootm 80a00000
netretry=no

Environment size: 960/131068 bytes
@>

[Кирилл]

Здравствуйте.
Среди переменных окружения не вижу МАС адреса устройства.
Вам необходимо остановить загрузку и ввести следующие переменные
set ethaddr xx:xx:xx:xx:xx:xx, где xx:xx:xx:xx:xx:xx необходимо заменить на реальный МАС адрес устройства (должен быть на наклейке)
set hostanme Altsag_MXA-24 (у вас прописано сейчас Altsag_M{A-24 -срецсимволы недопустимы)
save
reset

после этого должен запустится.

[Батор]

На 24-х отсутствует МАС адресс устройства.

[Кирилл]

Батор, поясните, что вы имели ввиду в поледнем комменте.

[Батор]

на шильдике не написан мас адрес

[Кирилл]

Серийный номер есть? если есть, пришлите его

[Батор]

547

[Кирилл]

Команды, которые должны быть введены:
set ethaddr 02:00:06:00:02:23
set hostanme Altsag_MXA-24
save
reset

[Батор]

Спасибо ,Кирилл.

[Кирилл]

Загрузка прошла?