МХА-24.Режим СLI

[Батор]

Здравствуйте! Не могу войти в режим СLI. Загрузка не проходит до конца.
@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
preboot=
ethact=
fwchange=run krnload; run fwerase; run krnflash;
krnload=tftp 80a00000 $(kernfile)
fwerase=erase bfc60000 c017ffff
krnflash=cp.b 80a00000 bfc60000 500000
ubchange=run ubload; run ubunprot; run uberase; run ubflash
ubunprot=protect off bfc00000 bfc3ffff
uberase=erase bfc00000 bfc3ffff
ubflash=cp.b 80a00000 bfc00000 34000
altbootcmd=run loadfkern;bootm 80a00000
loadfkern=cp.b bfc60000 80a00000 500000
flash_boot_name=u-boot.bin
vinterface=on
hostname=MXA
devicemodel=mxa24
mtu=1400
dslfile=dslam_v2.1.bin
dslcfgfile=dslam_v1.cfg
snmpfile=snmpd_v1
snmpcfgfile=snmpd_v1.conf
webfile=webs_v2.1
webpgfile=web_v2.1
clifile=cli
sysname=MXA
kernfile=uImage
ldrfile=u-boot.bin
ubload=tftp 80a00000 u-boot.bin
ethaddr=02:00:06:00:01:89
serverip=172.16.25.19
ipaddr=10.131.18.150
netmask=255.255.255.252
vlan=1509
gatewayip=10.131.18.149
bootcmd=run krnload;bootm 80a00000
netretry=no

Environment size: 968/131068 bytes
@>

[Батор]

U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Jun 23 2009 - 16:03:10)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1a1a0c20
Top of RAM usable for U-Boot at: 84000000
Reserving 452k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
-> DDR test:
................................
................................................
.................................................
.................................................
-> DDR test success!
SP at 0x83ecbf98 addr at 0x83f8c000
Relocate U-boot ...
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device MXA, host MXA
88e6131: ID 0x141 success!
IP: 10.131.18.150
Server IP: 172.16.25.19
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Oct 15 2009 10:46:18
***************************************
### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0
Using device
TFTP from server 172.16.25.19; our IP address is 10.131.18.150; sending through
gateway 10.131.18.149
Filename 'uImage'.
Load address: 0x80a00000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

Can't load from network
Load from FLASH, altbootcmd="run loadfkern;bootm 80a00000"


Copy 5242880 bytes .........................................

## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 6235340 Bytes = 5.9 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... Bad Data CRC
login: ****
password: *****
@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
preboot=
ethact=
fwchange=run krnload; run fwerase; run krnflash;
krnload=tftp 80a00000 $(kernfile)
fwerase=erase bfc60000 c017ffff
krnflash=cp.b 80a00000 bfc60000 500000
ubchange=run ubload; run ubunprot; run uberase; run ubflash
ubunprot=protect off bfc00000 bfc3ffff
uberase=erase bfc00000 bfc3ffff
ubflash=cp.b 80a00000 bfc00000 34000
altbootcmd=run loadfkern;bootm 80a00000
loadfkern=cp.b bfc60000 80a00000 500000
flash_boot_name=u-boot.bin
vinterface=on
hostname=MXA
devicemodel=mxa24
mtu=1400
dslfile=dslam_v2.1.bin
dslcfgfile=dslam_v1.cfg
snmpfile=snmpd_v1
snmpcfgfile=snmpd_v1.conf
webfile=webs_v2.1
webpgfile=web_v2.1
clifile=cli
sysname=MXA
kernfile=uImage
ldrfile=u-boot.bin
ubload=tftp 80a00000 u-boot.bin
ethaddr=02:00:06:00:01:89
serverip=172.16.25.19
ipaddr=10.131.18.150
netmask=255.255.255.252
vlan=1509
gatewayip=10.131.18.149
bootcmd=run krnload;bootm 80a00000
netretry=no

Environment size: 968/131068 bytes
@>

U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Jun 23 2009 - 16:03:10)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1b1b0c1f
Top of RAM usable for U-Boot at: 84000000
Reserving 452k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
-> DDR test:
................................
................................................
.................................................
.................................................
-> DDR test success!
SP at 0x83ecbf98 addr at 0x83f8c000
Relocate U-boot ...
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device MXA, host MXA
88e6131: ID 0x141 success!
IP: 10.131.18.150
Server IP: 172.16.25.19
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Oct 15 2009 10:46:18
***************************************
### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0
Using device
TFTP from server 172.16.25.19; our IP address is 10.131.18.150; sending through
gateway 10.131.18.149
Filename 'uImage'.
Load address: 0x80a00000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

Can't load from network
Load from FLASH, altbootcmd="run loadfkern;bootm 80a00000"


Copy 5242880 bytes .........................................

## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 6235340 Bytes = 5.9 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... Bad Data CRC
login:

здесь останавливается

[Кирилл]

Смотрите тему viewtopic.php?f=2&t=3247 или эту viewtopic.php?f=2&t=2661.

[Батор]

прописал переменные
set dslcfgfile dslam.cfg
set snmpfile snmpd_v2.1
set snmpcfgfile snmpd_v2.1.conf
set kernfile uImage_ip
set serverip your_tftp_server_ip
save


обновление ПО не происходит. Все остается на прежнем уровне.
set serverip ur_tftp_server_ip после выполнения ip адрес сервера 0.0.0.0
set serverip ur_tftp_server_ip 10.131.18.19 результат тот жеъ

nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
preboot=
ethact=
fwchange=run krnload; run fwerase; run krnflash;
krnload=tftp 80a00000 $(kernfile)
fwerase=erase bfc60000 c017ffff
krnflash=cp.b 80a00000 bfc60000 500000
ubchange=run ubload; run ubunprot; run uberase; run ubflash
ubunprot=protect off bfc00000 bfc3ffff
uberase=erase bfc00000 bfc3ffff
ubflash=cp.b 80a00000 bfc00000 34000
altbootcmd=run loadfkern;bootm 80a00000
loadfkern=cp.b bfc60000 80a00000 500000
flash_boot_name=u-boot.bin
vinterface=on
hostname=MXA
devicemodel=mxa24
mtu=1400
dslfile=dslam_v2.1.bin
webfile=webs_v2.1
webpgfile=web_v2.1
clifile=cli
sysname=MXA
ldrfile=u-boot.bin
ubload=tftp 80a00000 u-boot.bin
ethaddr=02:00:06:00:01:89
netmask=255.255.255.252
gatewayip=10.131.18.149
sset=serverip 10.131.18.19
ipaddr=10.131.18.20
serverip=10.131.18.19
dslcfgfile=dslam.cfg
snmpfile=snmpd_v2.1
snmpcfgfile=snmpd_v2.1.conf
kernfile=uImage_ip
bootcmd=run krnload;bootm 80a00000
netretry=no

Environment size: 988/131068 bytes
@>

[Кирилл]

set serverip your_tftp_server_ip- данная запись означает, что вместо your_tftp_server_ip вы должны подставить IP адрес своего tftp сервера.
После корректного ввода команд приложите лог запуска МХА.

[Батор]

U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Jun 23 2009 - 16:03:10)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1b1b0c1f
Top of RAM usable for U-Boot at: 84000000
Reserving 452k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
-> DDR test:
................................
................................................
.................................................
.................................................
-> DDR test success!
SP at 0x83ecbf98 addr at 0x83f8c000
Relocate U-boot ...
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device MXA, host MXA
88e6131: ID 0x141 success!
IP: 10.131.18.20
Server IP: 10.131.18.19
'vlan' not find, copy from servvlan
'servvlan' not find! check environments!!!
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Oct 15 2009 10:46:18
***************************************
### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0
Using device
TFTP from server 10.131.18.19; our IP address is 10.131.18.20; sending through g
ateway 10.131.18.149
Filename 'uImage_ip'.
Load address: 0x80a00000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

Can't load from network
Load from FLASH, altbootcmd="run loadfkern;bootm 80a00000"


Copy 5242880 bytes .........................................

## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 6235340 Bytes = 5.9 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... Bad Data CRC
login:

[Кирилл]

Либо не доступен сервер 10.131.18.19, либо на tftp сревре отсутствует файл uImage_ip.
P.S. Все файлы должны быть скачаны отсюда http://eltex.nsk.ru/sites/default/files/po/MXA-24%20(снято%20с%20производства)/MXA24.zip.zip/MXA24.zip