Обновление ПО на MXA32

[dorwi]

Здравствуйте! можно получить мануал по обновлению ПО на MXA32

[Кирилл]

Здравствуйте.
Можно http://элтекс.рф/upload/iblock/d71/ip_d ... a_2.4_.pdf
стр.133 -запуск обновления
стр/127 -задание адреса tftp сервера, на котором располагается файл прошивки

[dorwi]

Извиняюсь, что сразу не уточнил, могу попасть только в режим начального конфигурирования. Вообще проблема в том, что когда там я задаю параметры (IP,шлюз, vlan) все равно не могу попасть в режим управления коммутатором и также он не доступен по настроенному IP.
в консоли получаю:
U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Dec 24 2009 - 19:02:52)
UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1b1b0c1d
Top of RAM usable for U-Boot at: 84000000
Reserving 449k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
sp=0x83ecbf98 addr=0x83f8c000 => Relocate U-boot
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device ASL, host MXA
88e6131: ID 0x141 success!
IP: 1.1.58.86
Server IP: 192.168.0.70
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Feb 10 2010 02:24:16
***************************************
### main_loop: bootcmd="run nfsboot"
Hit any key to stop autoboot: 0
Using device
TFTP from server 192.168.0.70; our IP address is 1.1.58.86; sending through gateway 1.1.58.1
Filename 'uImage'.
Load address: 0x80a00000
Loading: T1 T1 T1 T1 T1 T1 T1 T1 T1 T1
Retry count exceeded; starting again

Can't load from network
Load from FLASH, altbootcmd="cp.b c0420000 80a00000 780000;bootm 80a00000"


Copy 7864320 bytes .............................................................

## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 6267357 Bytes = 6 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Comandline = flashboot
Reset FE tx bd index to zero ... Starting kernel at 0x801006d8 ...


LINUX started...
DETECTED system memsize: 67108864 bytes.
2Boot:[2]flashboot
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
Linux version 2.4.20-MVS (root@develop) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9))
#223 Mon Oct 13 16:29:17 NOVT 2014
Can't analyze prologue code at 8011ec18
Determined physical RAM map:
Initial ramdisk at: 0x8027d000 (5705728 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,57600
trap_init:board_be_init blocked
r4koff 1000000 CPU 200.00 MHz
Console: colour dummy device 80x25
Enable Watchdog driver
0.81 BogoMIPS
MIPS CPU counter frequency is fixed at 100000000 Hz
Memory: 56540k/57260k available (1316k kernel code, 720k reserved, 5676k data, 84k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware on host bus 0.Ignored
Initialize Diplomat-IP Fast Ethernet device.
Request IO region for FE Ethernet device, name=eth0.
eth0: TXC-FE ether at 0x280, using assigned IRQ 6
WARNING: A multicast kernel is in use.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
initialize_kbd: Keyboard failed self test
malta_int.c:the irq 1 is invalid
aSerial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI SERIAL_Diplomat-IP enabled
ttyS00 at 0x03f8 (irq = 3) is a ST16654
RAMDISK driver initialized: 1 RAM disks of 25000K size 1024 blocksize
loop: loaded (max 8 devices)
pld: version mxa32_v7.c Oct 13 2014 16:29:28
pld: image 78422 bytes, reset nCONFIG... ok, set nCONFIG... ok
loading: ....................OK
board_driver: ok!
init spi(twi) devices:
at26_driver: ok!
at26df321 device
mv6131_driver: ok!
data_driver: ok!
ibuf_driver: ok!
physmap flash device: 2000000 at 1fc00000
gl256: Found 1 x16 devices at 0x0 in 16-bit mode
num 1 mrf 1 id 227e
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Enabling fast programming.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cryptoapi: loaded
cryptoapi: Registered md5 (0)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 5572k freed
cnanda: make device for BOOT DISK.
cnanda: mount root file system...
VFS: Mounted root (ext2 filesystem).
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.7.2 (2010-04-16 10:13:30 MDT)
enter minte module
apply network from user config
ifconfig: eth0 mac A8:F9:4B:88:0E:D3 ip 192.168.1.2
netmask 255.255.255.0 gw 192.168.1.1 up
vconfig : eth0.150 up
eth0.150: add 01:00:5e:00:00:01 mcast address to master interface
apply configs name from user config
## Error: "loadfw" not defined
## Error: "devicemodel" not defined
>> decompress binary
mv: cannot rename '/mnt/.tgz': No such file or directory
tar: can't open '.tgz': No such file or directory
tar: can't open 'web.tgz': No such file or directory
mv: cannot rename '/wlog': No such file or directory
mv: cannot rename '/dfl': No such file or directory
mv: cannot rename '/cli': No such file or directory
mv: cannot rename '/enpu': No such file or directory
mv: cannot rename '/adsl': No such file or directory
mv: cannot rename '/mswi': No such file or directory
mv: cannot rename '/gbase': No such file or directory
mv: cannot rename '/snmpd': No such file or directory
mv: cannot rename '/webs': No such file or directory
mv: cannot rename '/sttcnf': No such file or directory
chmod: /bin/wlog: No such file or directory
chmod: /bin/cli: No such file or directory
chmod: /mnt/work/enpu: No such file or directory
chmod: /mnt/work/adsl: No such file or directory
chmod: /mnt/work/mswi: No such file or directory
chmod: /mnt/work/gbase: No such file or directory
chmod: /mnt/work/snmpd: No such file or directory
chmod: /mnt/work/webs: No such file or directory
chmod: /usr/sbin/sttcnf: No such file or directory
>> copy security
Can't find 'id=8' on flash
Can't find 'id=7' on flash
Can't find 'id=9' on flash
>> copy device config
syslogd: msg to /var/log/messages
webs: not found
wlog: not found
gbase: not found
enpu: not found
adsl: not found
mswi: not found
____________________________________________________________________________________________
может я конечно, что то делаю не так ?

[Кирилл]

В вашем случае нужно остановить загрузку и прописать сервер, с которого тянуть обновления
set serverip "you_tftp_serevr_ip_address"
save
reset

в корне тфтп сервера при этом должен лежать файл прошивки для МХА32 именованый как uImage.

[dorwi]

т.е все таки по логу видно, что есть какая то проблема с прошивкой ?. Как можно посмотреть установленную версию ПО ?

[Кирилл]

проблема втом, что на внутренюю память у вас ничего не записано, поэтому МХА не может ничего из нее поднять.
версии вы не посмотрите в таком состоянии.
сначала нужно загрузить МХА по сети (с тфтп).
Потом записасть ПО во внутренюю память через процедуру обновления.


Покажите еще вывод команды
print

[dorwi]

@>print
bootcmd=run nfsboot
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
ethaddr=10:11:12:40:2:40
preboot=
sysname=ASL
ethact=
krnload=tftp 80a00000 $(kernfile)
fwchange1=tftp 80a00000 $(kernfile);erase bfc60000 c03dffff;cp.b 80a00000 bfc60000 780000
fwchange2=tftp 80a00000 $(kernfile);erase c0420000 c0b9ffff;cp.b 80a00000 c0420000 780000
ubchange=tftp 80a00000 u-boot.bin;protect off bfc00000 bfc3ffff;erase bfc00000 bfc3ffff;cp.b 80a00000 bfc00000 34000
altbootcmd=cp.b c0420000 80a00000 780000;bootm 80a00000
kernfile=uImage
hostname=MXA
netmask=255.255.255.0
netretry=no
ipaddr=192.168.1.2
serverip=192.168.1.10
gatewayip=192.168.1.1
______________________________________________________________________
Щас проблема в том, что с коммутатора у меня нет пинга и наоборот с ПК.
коммутатор пишет ping 192.168.1.10
Using device
_______________________________________
Есть ли разница в какой интерфейс коммутатора подключаться ?

[Кирилл]

Вижу, что поплыли переменные окружения.
Выполните следующие команды:
set sysname MXA
set devicemodel mxa32
set bootcmd run krnload\;bootm 80a00000
save
reset


Должен по идее загрузится. Попробуйте. Если не стартанет, то напишите в каком месте затыкается.

[dorwi]

Dslam обновился, только вот чет также не могу попасть в управление(как я понимаю он должен быть доступен по IP 192.168.1.2 ?), в консоли отобразил log:

### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0
Using device
TFTP from server 192.168.1.10; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x80a00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################################
done
Bytes transferred = 5975545 (5b2df9 hex)
Download OK.
Return.
Begin env OK
Update env OK
## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 5975481 Bytes = 5.7 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Comandline = netboot
Reset FE tx bd index to zero ... Starting kernel at 0x801006d8 ...


LINUX started...
DETECTED system memsize: 67108864 bytes.
2Boot:[1]netboot
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
Linux version 2.4.20-MVS (root@develop) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.3-9))
#224 Mon Oct 13 16:40:46 NOVT 2014
Can't analyze prologue code at 8011ec18
Determined physical RAM map:
Initial ramdisk at: 0x8027d000 (5414912 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,57600
trap_init:board_be_init blocked
r4koff 1000000 CPU 200.00 MHz
Console: colour dummy device 80x25
Enable Watchdog driver
0.81 BogoMIPS
MIPS CPU counter frequency is fixed at 100000000 Hz
Memory: 56824k/57544k available (1316k kernel code, 720k reserved, 5392k data, 84k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware on host bus 0.Ignored
Initialize Diplomat-IP Fast Ethernet device.
Request IO region for FE Ethernet device, name=eth0.
eth0: TXC-FE ether at 0x280, using assigned IRQ 6
WARNING: A multicast kernel is in use.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
initialize_kbd: Keyboard failed self test
malta_int.c:the irq 1 is invalid
iSerial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI SERIAL_Diplomat-IP enabled
ttyS00 at 0x03f8 (irq = 3) is a ST16654
RAMDISK driver initialized: 1 RAM disks of 25000K size 1024 blocksize
loop: loaded (max 8 devices)
pld: version mxa64_v6.c Oct 13 2014 16:40:56
pld: image 78422 bytes, reset nCONFIG... ok, set nCONFIG... ok
loading: ....................OK
board_driver: ok!
board_Twi_SendByte: slave ACK fail
board_Twi_SendCmd: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_SendCmd: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Get1byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Set1byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Get1byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Set1byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Set2byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Set2byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Set2byte: addr fail
board_Twi_SendByte: slave ACK fail
board_Twi_Set2byte: addr fail
init spi(twi) devices:
at26_driver: ok!
at26df321 device
mv6131_driver: ok!
data_driver: ok!
ibuf_driver: ok!
physmap flash device: 2000000 at 1fc00000
gl256: Found 1 x16 devices at 0x0 in 16-bit mode
num 1 mrf 1 id 227e
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Enabling fast programming.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cryptoapi: loaded
cryptoapi: Registered md5 (0)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 5288k freed
cnanda: make device for BOOT DISK.
cnanda: mount root file system...
VFS: Mounted root (ext2 filesystem).
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.7.2 (2010-04-16 10:13:30 MDT)
enter minte module
apply network from user config
ifconfig: eth0 mac A8:F9:4B:88:0E:D3 ip 192.168.1.2
netmask 255.255.255.0 gw 192.168.1.1 up
vconfig : eth0.150 up
eth0.150: add 01:00:5e:00:00:01 mcast address to master interface
apply configs name from user config
## Error: "loadfw" not defined
>> decompress binary
mv: cannot rename '/mnt/mxa32.tgz': No such file or directory
tar: can't open 'mxa32.tgz': No such file or directory
tar: can't open 'web.tgz': No such file or directory
mv: cannot rename '/wlog': No such file or directory
mv: cannot rename '/dfl': No such file or directory
mv: cannot rename '/cli': No such file or directory
mv: cannot rename '/enpu': No such file or directory
mv: cannot rename '/adsl': No such file or directory
mv: cannot rename '/mswi': No such file or directory
mv: cannot rename '/gbase': No such file or directory
mv: cannot rename '/snmpd': No such file or directory
mv: cannot rename '/webs': No such file or directory
mv: cannot rename '/sttcnf': No such file or directory
chmod: /bin/wlog: No such file or directory
chmod: /bin/cli: No such file or directory
chmod: /mnt/work/enpu: No such file or directory
chmod: /mnt/work/adsl: No such file or directory
chmod: /mnt/work/mswi: No such file or directory
chmod: /mnt/work/gbase: No such file or directory
chmod: /mnt/work/snmpd: No such file or directory
chmod: /mnt/work/webs: No such file or directory
chmod: /usr/sbin/sttcnf: No such file or directory
>> copy security
Can't find 'id=8' on flash
Can't find 'id=7' on flash
Can't find 'id=9' on flash
>> copy device config
syslogd: msg to /var/log/messages
webs: not found
wlog: not found
gbase: not found
enpu: not found
adsl: not found
mswi: not found

[Кирилл]

переменные прописали, по моему комментарию выше?

[dorwi]

@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
ethaddr=10:11:12:40:2:40
preboot=
ethact=
krnload=tftp 80a00000 $(kernfile)
fwchange1=tftp 80a00000 $(kernfile);erase bfc60000 c03dffff;cp.b 80a00000 bfc60000 780000
fwchange2=tftp 80a00000 $(kernfile);erase c0420000 c0b9ffff;cp.b 80a00000 c0420000 780000
ubchange=tftp 80a00000 u-boot.bin;protect off bfc00000 bfc3ffff;erase bfc00000 bfc3ffff;cp.b 80a00000 bfc00000 34000
altbootcmd=cp.b c0420000 80a00000 780000;bootm 80a00000
kernfile=uImage
hostname=MXA
netmask=255.255.255.0
ipaddr=192.168.1.2
serverip=192.168.1.10
gatewayip=192.168.1.1
sysname=MXA
devicemodel=mxa32
bootcmd=run krnload;bootm 80a00000
netretry=no
______________________________________
все прописал, коммутатор только после этого обновился, и далее также не загружается.

[Кирилл]

Софт точно для МХА32 загружаете?
перекачайте http://элтекс.рф/upload/iblock/f50/uima ... 0_2014.zip, распакуйте, переименуйте uImage32 в uImage

[dorwi]

сорри еще раз ... конечно... обновлял ПО для MXA64 ))... обновил, проверю ... отпишу

[dorwi]

большое спасибо за помощь, все работает.