smg-2016 по PRI с LG CS1000

[vkrt]

Получили SMG-2016? начал настраивать линки со станциями.
Первая LG CS1000 network. SMG - user.
вызов с sip абонента 7500 зарегистрированного на smg.
Большинство вызовов не проходит:
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log started at: 20:39:44.702225 16/08/18
Trace levels:
alarm - 00
calls - 00
isup - 00
q931 - 01
sipt - 00
rtp - 00
msp - 00
radius - 00
h323 - 00
ivr - 00
20:39:51.138086 [INFO] Q931. Line 00/00. Create Call, entry 124. Call 001C (Outgoing)
20:39:51.138148 [INFO] Q931. Line 00/00. Search B-chan: chan -1, mask 00010001 {chan mask: 40010001} - chan order: 0, dir=-1, start=31
20:39:51.138177 [INFO] Q931. Line 00/00. Search B-chan: chan -1, mask 00010001 {chan mask: 40010001} - found free chan 31 (cycle dir 1)
20:39:51.138221 [INFO] Q931. Line 00/00. Setup from SIPT:0321 (enblock)
20:39:51.138250 [INFO] Q931. Line 00/00. Call 001C. State 'Null'
20:39:51.138285 [INFO] Q931. Line 00/00. Call 001C. 'Dial' in state 'Null'. <6>(1)
20:39:51.138315 [INFO] Q931. Line 00/00. Call 001C. 'OutDial' result [0]
20:39:51.138346 [INFO] Q931. Line 00/00. Call 001C. 'Dial' in state 'Null'. <2>(1)
20:39:51.138376 [INFO] Q931. Line 00/00. Call 001C. 'OutDial' result [0]
20:39:51.138406 [INFO] Q931. Line 00/00. Call 001C. 'Dial' in state 'Null'. <9>(1)
20:39:51.138435 [INFO] Q931. Line 00/00. Call 001C. 'OutDial' result [0]
20:39:51.138466 [INFO] Q931. Line 00/00. Call 001C. 'Dial' in state 'Null'. <0.>(2)
20:39:51.138497 [INFO] Q931. Line 00/00. Call 001C. 'OutDial' result [2]
20:39:51.138526 [INFO] Q931. Line 00/00. Call 001C. Seize out (enblock)
20:39:51.138559 [INFO] Q931. Line 00/00. Search B-chan: chan 31, mask 00010001 - chan used by CR=001c
20:39:51.138586 [INFO] Q931. Line 00/00. Search B-chan: chan 31, mask 00010001 - chan ok: mask 00010001
20:39:51.138612 [INFO] Q931. Line 00/00. Call 001C. Create Seize - entry 124, channel 31
20:39:51.138640 [INFO] Q931. Line 00/00. Call 001C. State 'Call Initiated'
20:39:51.138668 [INFO] Q931. Line 00/00. Call 001C. Timer 'T303' (4 sec) start in state 'Call Initiated'
20:39:51.138753 [INFO] Q931. Line 00/00. Call 001C. TX 37
DUMP: 08.02.00.1C.05.A1.04.03.90.90.A3.18.03.A9.83.9F.
1E.02.80.83.6C.06.41.83.37.35.30.30.70.05.81.36.
32.39.30.A1.
0x001C (from orig), MSG=SETUP:
[sending complete]
[bearer capability:
cap=3.1 kHz audio
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=31 (exclusive)] Coding=CCITT
[progress ind: Origin not isdn (3)]
[calling party number: 7500 (type=subscriber, plan=ISDN, present.allowed, network provided)]
[called party number: 6290 (type=unknown, plan=ISDN)]
[sending complete]
---------------------------------
20:39:51.679916 [INFO] Q931. Line 00/00. Call 001B. Timer 'T305' expired in state 'Disconnect Request'
20:39:51.679961 [INFO] Q931. Line 00/00. Call 001B. State 'Release Request'
20:39:51.679991 [INFO] Q931. Line 00/00. Call 001B. Timer 'T308' (4 sec) start in state 'Release Request'
20:39:51.680040 [INFO] Q931. Line 00/00. Call 001B. TX 10
DUMP: 08.02.00.1B.4D.08.02.80.E6.
0x001B (from orig), MSG=RELEASE:
[cause: Recovery on time expiry (location=user, std=CCITT)]
---------------------------------
20:39:55.184906 [INFO] Q931. Line 00/00. Call 001C. Timer 'T303' expired in state 'Call Initiated'
20:39:55.184954 [INFO] Q931. Line 00/00. Call 001C. Should DISCONNECT.
20:39:55.185232 [INFO] Q931. Line 00/00. Call 001C. Disconnect call in state 'Call Initiated'
20:39:55.185278 [INFO] Q931. Line 00/00. Call 001C. State 'Disconnect Request'
20:39:55.185312 [INFO] Q931. Line 00/00. Call 001C. Timer 'T305' (30 sec) start in state 'Disconnect Request'
20:39:55.185367 [INFO] Q931. Line 00/00. Call 001C. TX 10
DUMP: 08.02.00.1C.45.08.02.80.E6.
0x001C (from orig), MSG=DISCONNECT:
[cause: Recovery on time expiry (location=user, std=CCITT)]
---------------------------------
20:39:55.685632 [INFO] Q931. Line 00/00. Call 001B. Timer 'T308' expired in state 'Release Request'
20:39:55.685712 [INFO] Q931. Line 00/00. Call 001B. Timer 'T308' (4 sec) start in state 'Release Request'
20:39:55.685766 [INFO] Q931. Line 00/00. Call 001B. TX 10
DUMP: 08.02.00.1B.4D.08.02.80.E6.
0x001B (from orig), MSG=RELEASE:
[cause: Recovery on time expiry (location=user, std=CCITT)]
---------------------------------
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log stopped at: 20:39:59.021722 16/08/18
Редко проходят:
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log started at: 20:45:24.447168 16/08/18
Trace levels:
alarm - 00
calls - 00
isup - 00
q931 - 01
sipt - 00
rtp - 00
msp - 00
radius - 00
h323 - 00
ivr - 00
20:45:31.523763 [INFO] Q931. Line 00/00. Create Call, entry 125. Call 001D (Outgoing)
20:45:31.523826 [INFO] Q931. Line 00/00. Search B-chan: chan -1, mask 00010001 {chan mask: 00010001} - chan order: 0, dir=-1, start=0
20:45:31.523856 [INFO] Q931. Line 00/00. Search B-chan: chan -1, mask 00010001 {chan mask: 00010001} - found free chan 1 (cycle dir 1)
20:45:31.523899 [INFO] Q931. Line 00/00. Setup from SIPT:0043 (enblock)
20:45:31.523928 [INFO] Q931. Line 00/00. Call 001D. State 'Null'
20:45:31.523963 [INFO] Q931. Line 00/00. Call 001D. 'Dial' in state 'Null'. <6>(1)
20:45:31.523994 [INFO] Q931. Line 00/00. Call 001D. 'OutDial' result [0]
20:45:31.524025 [INFO] Q931. Line 00/00. Call 001D. 'Dial' in state 'Null'. <2>(1)
20:45:31.524054 [INFO] Q931. Line 00/00. Call 001D. 'OutDial' result [0]
20:45:31.524084 [INFO] Q931. Line 00/00. Call 001D. 'Dial' in state 'Null'. <9>(1)
20:45:31.524114 [INFO] Q931. Line 00/00. Call 001D. 'OutDial' result [0]
20:45:31.524144 [INFO] Q931. Line 00/00. Call 001D. 'Dial' in state 'Null'. <0.>(2)
20:45:31.524175 [INFO] Q931. Line 00/00. Call 001D. 'OutDial' result [2]
20:45:31.524204 [INFO] Q931. Line 00/00. Call 001D. Seize out (enblock)
20:45:31.524237 [INFO] Q931. Line 00/00. Search B-chan: chan 1, mask 00010001 - chan used by CR=001d
20:45:31.524266 [INFO] Q931. Line 00/00. Search B-chan: chan 1, mask 00010001 - chan ok: mask 00010001
20:45:31.524294 [INFO] Q931. Line 00/00. Call 001D. Create Seize - entry 125, channel 01
20:45:31.524322 [INFO] Q931. Line 00/00. Call 001D. State 'Call Initiated'
20:45:31.524350 [INFO] Q931. Line 00/00. Call 001D. Timer 'T303' (4 sec) start in state 'Call Initiated'
20:45:31.524435 [INFO] Q931. Line 00/00. Call 001D. TX 37
DUMP: 08.02.00.1D.05.A1.04.03.90.90.A3.18.03.A9.83.81.
1E.02.80.83.6C.06.41.83.37.35.30.30.70.05.81.36.
32.39.30.A1.
0x001D (from orig), MSG=SETUP:
[sending complete]
[bearer capability:
cap=3.1 kHz audio
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=1 (exclusive)] Coding=CCITT
[progress ind: Origin not isdn (3)]
[calling party number: 7500 (type=subscriber, plan=ISDN, present.allowed, network provided)]
[called party number: 6290 (type=unknown, plan=ISDN)]
[sending complete]
---------------------------------
20:45:31.715628 [INFO] Q931. Line 00/00. Call 001D. RX 14
DUMP: 08.02.80.1D.02.18.03.A9.83.81.1E.02.81.88.
0x001D (to orig), MSG=CALL PROCEEDING:
[channel id: channel=1 (exclusive)] Coding=CCITT
[progress ind: In-band signal (8)]
---------------------------------
20:45:31.715678 [INFO] Q931. Line 00/00. Call 001D. Timer 'T303' stop in state 'Call Initiated'
20:45:31.715710 [INFO] Q931. Line 00/00. Call 001D. SetISDN: allway[1], fwd_acs[0]. Stage [1]
20:45:31.715739 [INFO] Q931. Line 00/00. Call 001D. Switch v-chan
20:45:31.716040 [INFO] Q931. Line 00/00. Call 001D. State 'Outgoing Call Proceeding'
20:45:36.377944 [INFO] Q931. Line 00/00. Call 001D. RX 10
DUMP: 08.02.80.1D.01.18.03.A9.83.81.
0x001D (to orig), MSG=ALERTING:
[channel id: channel=1 (exclusive)] Coding=CCITT
---------------------------------
20:45:36.378001 [INFO] Q931. Line 00/00. Call 001D. Timer 'T301' (180 sec) start in state 'Outgoing Call Proceeding'
20:45:36.378032 [INFO] Q931. Line 00/00. Call 001D. State 'Call Delivered'
20:45:38.464783 [INFO] Q931. Line 00/00. Call 001D. RX 5
DUMP: 08.02.80.1D.07.
0x001D (to orig), MSG=CONNECT:
---------------------------------
20:45:38.464850 [INFO] Q931. Line 00/00. Call 001D. Timer 'T301' stop in state 'Call Delivered'
20:45:38.464914 [INFO] Q931. Line 00/00. Call 001D. State 'Active'
20:45:38.464956 [INFO] Q931. Line 00/00. Call 001D. TX 6
DUMP: 08.02.00.1D.0F.
0x001D (from orig), MSG=CONNECT ACKNOWLEDGE:
---------------------------------
20:45:42.660880 [INFO] Q931. Line 00/00. Call 001D. RX 9
DUMP: 08.02.80.1D.45.08.02.81.90.
0x001D (to orig), MSG=DISCONNECT:
[cause: Normal call clearing (location=private network serving local user, std=CCITT)]
---------------------------------
20:45:42.660935 [INFO] Q931. Line 00/00. Call 001D. Recv 'Disconnect'. Cause: 'Normal call clearing'
20:45:42.660965 [INFO] Q931. Line 00/00. Call 001D. State 'Release Request'
20:45:42.660995 [INFO] Q931. Line 00/00. Call 001D. Timer 'T308' (4 sec) start in state 'Release Request'
20:45:42.661039 [INFO] Q931. Line 00/00. Call 001D. TX 10
DUMP: 08.02.00.1D.4D.08.02.81.90.
0x001D (from orig), MSG=RELEASE:
[cause: Normal call clearing (location=private network serving local user, std=CCITT)]
---------------------------------
20:45:43.720234 [INFO] Q931. Line 00/00. Call 001D. RX 9
DUMP: 08.02.80.1D.5A.08.02.81.90.
0x001D (to orig), MSG=RELEASE COMPLETE:
[cause: Normal call clearing (location=private network serving local user, std=CCITT)]
---------------------------------
20:45:43.720297 [INFO] Q931. Line 00/00. Call 001D. Recv 'Release complete'. Cause: 'Normal call clearing'
20:45:43.720346 [INFO] Q931. Line 00/00. Call 001D. State 'Null'
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log stopped at: 20:45:46.604157 16/08/18
C входящими чуть лучше, но тоже не всегда.
Удачный входящий вызов:
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log started at: 20:49:04.182381 16/08/18
Trace levels:
alarm - 00
calls - 00
isup - 00
q931 - 01
sipt - 00
rtp - 00
msp - 00
radius - 00
h323 - 00
ivr - 00
20:49:13.307076 [INFO] Q931. Line 00/00. Call EC10. RX 23
DUMP: 08.02.6C.10.05.04.03.80.90.A3.18.03.A1.83.9C.6C.
06.21.81.37.31.37.30.
0x6C10 (from orig), MSG=SETUP:
[bearer capability:
cap=speech
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=28 (preferred)] Coding=CCITT
[calling party number: 7170 (type=national, plan=ISDN, present.allowed, verifed & pass)]
---------------------------------
20:49:13.307126 [INFO] Q931. Line 00/00. Create Call, entry 00. Call EC10 (Incoming)
20:49:13.307160 [INFO] Q931. Line 00/00. Call EC10. Incoming SETUP. Check chan id
20:49:13.307191 [INFO] Q931. Line 00/00. Call EC10. Check IE 'Channel ID': channel id='as indicated'chan=28, mode non-excl
20:49:13.307223 [INFO] Q931. Line 00/00. Search B-chan: chan 28, mask 00010001 - chan ok: mask 00010001
20:49:13.307254 [INFO] Q931. Line 00/00. Call EC10. Check IE 'Bearer capablity': {speech}{64 kbit/s}{G.711 A-law}
20:49:13.307288 [INFO] Q931. Line 00/00. Call EC10. Check IE 'Calling party number': {type=0x02, plan=0x01}, {presentation=0, screening=1} <7170> (4)
20:49:13.307315 [INFO] Q931. Line 00/00. Call EC10. Incoming SETUP. CgPN <7170>(4), CdPN <>(0) isdn flag=03
20:49:13.307371 [INFO] Q931. Line 00/00. Call EC10. Incoming seize - PLAN 0. COS 0
20:49:13.307401 [INFO] Q931. Line 00/00. Call EC10. Incoming SETUP. proc dial
20:49:13.307429 [INFO] Q931. Line 00/00. Call EC10. State 'Overlap Receiving'
20:49:13.307458 [INFO] Q931. Line 00/00. Call EC10. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
20:49:13.307502 [INFO] Q931. Line 00/00. Call EC10. TX 11
DUMP: 08.02.EC.10.0D.18.03.A9.83.9C.
0x6C10 (to orig), MSG=SETUP ACKNOWLEDGE:
[channel id: channel=28 (exclusive)] Coding=CCITT
---------------------------------
20:49:13.367903 [INFO] Q931. Line 00/00. Call EC10. RX 12
DUMP: 08.02.6C.10.7B.70.05.80.37.35.30.30.
0x6C10 (from orig), MSG=INFORMATION:
[called party number: 7500 (type=unknown, plan=unknown)]
---------------------------------
20:49:13.367946 [INFO] Q931. Line 00/00. Call EC10. Check IE 'Called party number': {type=0x00, plan=0x00} <7500> (4)
20:49:13.367977 [INFO] Q931. Line 00/00. Call EC10. In Dial: 7500
20:49:13.368007 [INFO] Q931. Line 00/00. Call EC10. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
20:49:13.368055 [INFO] Q931. Line 00/00. Call EC10. End Dial in state 'Overlap Receiving' (condition for call proceeding reached)
20:49:13.368086 [INFO] Q931. Line 00/00. Call EC10. Timer 'T302' stop in state 'Overlap Receiving'
20:49:13.368123 [INFO] Q931. Line 00/00. Call EC10. TX 6
DUMP: 08.02.EC.10.02.
0x6C10 (to orig), MSG=CALL PROCEEDING:
---------------------------------
20:49:13.368157 [INFO] Q931. Line 00/00. Call EC10. State 'Incoming Call Proceeding'
20:49:13.375894 [INFO] Q931. Line 00/00. Call EC10. Call Received. PI [1][0]
20:49:13.375946 [INFO] Q931. Line 00/00. Call EC10. Send 'Alert'
20:49:13.375994 [INFO] Q931. Line 00/00. Call EC10. TX 10
DUMP: 08.02.EC.10.01.1E.02.80.81.
0x6C10 (to orig), MSG=ALERTING:
[progress ind: No end-to-end isdn (1)]
---------------------------------
20:49:13.376033 [INFO] Q931. Line 00/00. Call EC10. State 'Call Received'
20:49:17.120738 [INFO] Q931. Line 00/00. Call EC10. Answer
20:49:17.120794 [INFO] Q931. Line 00/00. Call EC10. Send 'Answer'. PI-sent[2]
20:49:17.120840 [INFO] Q931. Line 00/00. Call EC10. State 'Active'
20:49:17.120884 [INFO] Q931. Line 00/00. Call EC10. TX 6
DUMP: 08.02.EC.10.07.
0x6C10 (to orig), MSG=CONNECT:
---------------------------------
20:49:18.206735 [INFO] Q931. Line 00/00. Call EC10. RX 5
DUMP: 08.02.6C.10.0F.
0x6C10 (from orig), MSG=CONNECT ACKNOWLEDGE:
---------------------------------
20:49:20.870546 [INFO] Q931. Line 00/00. Call EC10. Disconnect call in state 'Active'
20:49:20.870603 [INFO] Q931. Line 00/00. Call EC10. State 'Disconnect Request'
20:49:20.870636 [INFO] Q931. Line 00/00. Call EC10. Timer 'T305' (30 sec) start in state 'Disconnect Request'
20:49:20.870687 [INFO] Q931. Line 00/00. Call EC10. TX 10
DUMP: 08.02.EC.10.45.08.02.80.90.
0x6C10 (to orig), MSG=DISCONNECT:
[cause: Normal call clearing (location=user, std=CCITT)]
---------------------------------
20:49:21.343463 [INFO] Q931. Line 00/00. Call EC10. RX 9
DUMP: 08.02.6C.10.4D.08.02.81.90.
0x6C10 (from orig), MSG=RELEASE:
[cause: Normal call clearing (location=private network serving local user, std=CCITT)]
---------------------------------
20:49:21.343513 [INFO] Q931. Line 00/00. Call EC10. Recv 'Release'. Cause: 'Normal call clearing'
20:49:21.343551 [INFO] Q931. Line 00/00. Call EC10. TX 6
DUMP: 08.02.EC.10.5A.
0x6C10 (to orig), MSG=RELEASE COMPLETE:
---------------------------------
20:49:21.343606 [INFO] Q931. Line 00/00. Call EC10. State 'Null'
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log stopped at: 20:49:23.642532 16/08/18
А вот неудачный:
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log started at: 20:50:29.004013 16/08/18
Trace levels:
alarm - 00
calls - 00
isup - 00
q931 - 01
sipt - 00
rtp - 00
msp - 00
radius - 00
h323 - 00
ivr - 00
20:50:35.070344 [INFO] Q931. Line 00/00. Call ECC0. RX 23
DUMP: 08.02.6C.C0.05.04.03.80.90.A3.18.03.A1.83.9D.6C.
06.21.81.37.31.37.30.
0x6CC0 (from orig), MSG=SETUP:
[bearer capability:
cap=speech
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=29 (preferred)] Coding=CCITT
[calling party number: 7170 (type=national, plan=ISDN, present.allowed, verifed & pass)]
---------------------------------
20:50:35.070400 [INFO] Q931. Line 00/00. Create Call, entry 02. Call ECC0 (Incoming)
20:50:35.070434 [INFO] Q931. Line 00/00. Call ECC0. Incoming SETUP. Check chan id
20:50:35.070466 [INFO] Q931. Line 00/00. Call ECC0. Check IE 'Channel ID': channel id='as indicated'chan=29, mode non-excl
20:50:35.070499 [INFO] Q931. Line 00/00. Search B-chan: chan 29, mask 00010001 - chan ok: mask 00010001
20:50:35.070529 [INFO] Q931. Line 00/00. Call ECC0. Check IE 'Bearer capablity': {speech}{64 kbit/s}{G.711 A-law}
20:50:35.070563 [INFO] Q931. Line 00/00. Call ECC0. Check IE 'Calling party number': {type=0x02, plan=0x01}, {presentation=0, screening=1} <7170> (4)
20:50:35.070591 [INFO] Q931. Line 00/00. Call ECC0. Incoming SETUP. CgPN <7170>(4), CdPN <>(0) isdn flag=03
20:50:35.070646 [INFO] Q931. Line 00/00. Call ECC0. Incoming seize - PLAN 0. COS 0
20:50:35.070677 [INFO] Q931. Line 00/00. Call ECC0. Incoming SETUP. proc dial
20:50:35.070704 [INFO] Q931. Line 00/00. Call ECC0. State 'Overlap Receiving'
20:50:35.070733 [INFO] Q931. Line 00/00. Call ECC0. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
20:50:35.070778 [INFO] Q931. Line 00/00. Call ECC0. TX 11
DUMP: 08.02.EC.C0.0D.18.03.A9.83.9D.
0x6CC0 (to orig), MSG=SETUP ACKNOWLEDGE:
[channel id: channel=29 (exclusive)] Coding=CCITT
---------------------------------
20:50:39.307548 [INFO] Q931. Line 00/00. Call ECC0. RX 23
DUMP: 08.02.6C.C0.05.04.03.80.90.A3.18.03.A1.83.9D.6C.
06.21.81.37.31.37.30.
0x6CC0 (from orig), MSG=SETUP:
[bearer capability:
cap=speech
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=29 (preferred)] Coding=CCITT
[calling party number: 7170 (type=national, plan=ISDN, present.allowed, verifed & pass)]
---------------------------------
20:50:39.307590 [ERR ] Q931. Line 00/00. CallRef ECC0 active. SETUP ignored. Call state Overlap Receiving
SMG-2016_rev.B. SN: VI5A000190 Software Version: ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Log stopped at: 20:50:47.166910 16/08/18
Неудачи входящих обычно возникают после неудачного исходящего.
Поток станции LG CS1000 вполне себе рабочий (работал до этого с iP LDK100), был взят на время тестирования.
Программное обеспечение:
Версия ПО ECSS-10 V.3.10.0.2447 2016/PBX/H323/VAS/REC/IVR Build: Dec 13 2017 10:26:27
Версия SIP-адаптера 3.10.0.35
IVR модуль 0 0.0.2.72.212786-0.0.2.78.902724
IVR модуль 1 3.4.1.60.458505-3.4.1.60.089154

Заводские параметры:
Модель SMG-2016_rev.B
Ревизия 1V18

[Dmitriy_eltex]

Здравствуйте.

На будущее, хотелось бы Вас попросить прикладывать логи отдельными файлами, а не кидать в форум.
Найти Ваши коментарии среди 1000 строчек, не так просто, как Вы думаете.

В случае исходящего вызова видно, что истекает T305, потому что иногда LG CS1000 не отвечает на наш вызов.
В случае входящего тоже самое: шлем на их вызов SETUP ACK, но они выполняют перепосыл SETUP.

Нужно задать вопрос в support LG: периодически они не видят/игнорируют наши сигнальные сообщения Q.931, почему?
Ну и логи не полные, чтобы разобраться пришлите на почту в моей подписи:
1) Конфигурацию Вашей SMG (Сервис->Управление файлами конфигурации->Скачать);
2) Лог PBX_PSTN неудачного звонка все уровни 1 (Раздел PBX трассировки).
3) Название Вашей компании и город.