Подскажите, проблема с TAU-i8. За день пару раз падает шлюз во время разговора.
Пытаемся сразу зайти на шлюз через веб. Шлюз висит. Телефоны не работают.
Минуты через 3 все приходит в норму. Начинает работать веб и телефоны.
В чем может быть проблема.
Код: Выделить всё
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 248MB = 248MB total
Memory: 246784KB available (4280K code, 279K data, 132K init, 0K highmem)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:80
Calibrating delay loop... 648.80 BogoMIPS (lpj=3244032)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
SPI core: loaded version 0.2
PCIe0: no device detected on link (11)
PCIe1: no device detected on link (3)
pcie_setup(0)
pcie_scan_bus(0)
pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
pci 0000:00:00.0: supports D1
pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold
pci 0000:00:00.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
pcie_setup(1)
pcie_scan_bus(1)
PCI: bus1: Fast back to back transfers enabled
slot 0, pin 1, irq 68
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x4000ffff 64bit]
pci 0000:00:00.0: BAR 0: set to [mem 0x40000000-0x4000ffff 64bit] (PCI address [0x40000000-0x4000ffff]
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 32 bytes, default 32
SPI core: add adapter comcerto-spi
arm1: Module loaded.
Registering mini_fo version $Id: 209-mini_fo.patch,v 1.1.2.1 2010/06/21 09:34:58 satananda.burla Exp $
Slow work thread pool: Starting up
Slow work thread pool: Ready
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
msgmni has been set to 482
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
console [ttyS0] enabled
loop: module loaded
nbd: registered device at major 43
st: Version 20081215, fixed bufsize 32768, s/g segs 256
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks
7 cmdlinepart partitions found on MTD device comcertonand
Creating 7 MTD partitions on "comcertonand":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000060000 : "env"
0x000000060000-0x000000260000 : "config"
0x000000260000-0x000000660000 : "kernel"
0x000000660000-0x000001dd0000 : "fs"
0x000001dd0000-0x000001fc4000 : "driver"
0x000001fc4000-0x000001fd4000 : "default_config"
c1k_eth_probe: gemac 0
PHY ID1=001C ID2=C816
Configure GEMAC0 as MII for RTL8201FL
Start link timer
eth0: C1000 Ethernet Controller a8:f9:4b:02:de:f1
c1k_eth_probe: gemac 1
PHY ID1=001C ID2=C816
eth2: C1000 Ethernet Controller 02:20:80:a8:f9:4b
MDC divider: 96
Comcerto MDIO Bus: probed
MDC divider: 96
Comcerto MDIO Bus: probed
eth1 init
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoE module inited
PPPoL2TP kernel driver, V1.0
usbcore: registered new interface driver catc
catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
usbcore: registered new interface driver kaweth
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
usbcore: registered new interface driver rtl8150
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_eem
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver smsc95xx
usbcore: registered new interface driver gl620a
usbcore: registered new interface driver net1080
usbcore: registered new interface driver plusb
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver MOSCHIP usb-ethernet driver
usbcore: registered new interface driver int51x1
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver huawei_cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
tdi_reset: set Streaming disable mode
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: comcerto EHCI
comcerto-ehci comcerto-ehci.1: new USB bus registered, assigned bus number 1
comcerto-ehci comcerto-ehci.1: irq 5, io mem 0x0f000000
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: comcerto EHCI
usb usb1: Manufacturer: Linux 2.6.33.5 ehci_hcd
usb usb1: SerialNumber: comcerto-ehci.1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for IPWireless converter
usbcore: registered new interface driver ipwtty
ipw: v0.3:IPWireless tty driver
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
i2c /dev entries driver
comcerto_i2c_init: module loaded
cpuidle: using governor ladder
(NTE-)RG: init eltex watchdog
nf_conntrack version 0.5.0 (3859 buckets, 15436 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing NETLINK_KEY socket
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
VFS: Mounted root (jffs2 filesystem) readonly on device 31:4.
Freeing init memory: 132K
Please be patient, while OpenWrt loads ...
board: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
Init proprietary Eltex NTE-RG/RG board driver
Board info available
Board type: TAU
Board switch to normal mode
-----------------------------------------------------
Registering the module 'slic' for Si3217x device
-----------------------------------------------------
Compilation date: Feb 21 2017 at 08:34:11.
Borad_type: TAU-8.IP
Set major number 64.
SPI core: add driver si3217x
SPI core: attach client to adapter comcerto-spi
slic0 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic1 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic2 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic3 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic4 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic5 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic6 device probe. Chip ID: 0xa1 si32176 rev.B
SPI core: attach client to adapter comcerto-spi
slic7 device probe. Chip ID: 0xa1 si32176 rev.B
-----------------------------------------------------
Device initialization.
-----------------------------------------------------
slic0 start init
slic1 start init
slic2 start init
slic3 start init
slic4 start init
slic5 start init
slic6 start init
slic7 start init
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
Compat-wireless backport release: compat-wireless-2.6.38-3-ns
Backport based on linux-2.6-allstable.git v2.6.38
cfg80211: Calling CRDA to update world regulatory domain
slic0 start calibration
slic1 start calibration
slic2 start calibration
slic3 start calibration
slic4 start calibration
slic5 start calibration
slic6 start calibration
slic7 start calibration
PCI: enabling device 0000:00:00.0 (0140 -> 0142)
PCI: Setting latency timer of device 0000:00:00.0 to 64
ath: EEPROM regdomain sanitized
ath: EEPROM regdomain: 0x61
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x61
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @ KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xd01a0000, irq=68
ADDRCONF(NETDEV_UP): wlan0: link is not ready
slic0 calibration complete
slic1 calibration complete
slic2 calibration complete
slic3 calibration complete
slic4 calibration complete
slic5 calibration complete
slic6 calibration complete
slic7 calibration complete
slic0 init done
slic1 init done
slic2 init done
slic3 init done
slic4 init done
slic5 init done
slic6 init done
slic7 init done
Init Eltex conntrack driver
c1k_eth_open: eth0
Disabling GEM0 delay
comcerto gemac0 software config using MII
comcerto gemac0 software config FULL DUPLEX
comcerto gemac0 software config SPEED 100M
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
platform MSP Copro: firmware: requesting msp.axf
MSP is running
drivers/net/comcerto/comcerto_ved.c: 569: info
Device=170
Revision=0
spu_version=Arm11DspV_5_8_3
CSPtoMSPQueuePhyaddr=a000500
MSPtoCSPQueuePhyaddr=a000510
SMRXCSPhyaddr=a000520
SMTXCSPhyaddr=a000520
MSP version is : Test_v601_13_78771_1
NET: Registered protocol family 27
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
Netfilter messages via NETLINK v0.30.
ctnetlink v0.93: registering with nfnetlink.
eth0: c1k_eth_close
c1k_eth_open: eth0
Disabling GEM0 delay
comcerto gemac0 software config using MII
comcerto gemac0 software config FULL DUPLEX
comcerto gemac0 software config SPEED 100M
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
slic0: Set hook_min_clr=500ms
slic0: Set hook_min_ko=200ms
slic0: Set hook_max_pd=100ms
slic0: Set hook_dig_interval=200ms
slic0: Set line->pcm gain!
slic0: Set pcm->line gain!
slic1: Set hook_min_clr=500ms
slic1: Set hook_min_ko=200ms
slic1: Set hook_max_pd=100ms
slic1: Set hook_dig_interval=200ms
slic1: Set line->pcm gain!
slic1: Set pcm->line gain!
slic2: Set hook_min_clr=500ms
slic2: Set hook_min_ko=200ms
slic2: Set hook_max_pd=100ms
slic2: Set hook_dig_interval=200ms
slic2: Set line->pcm gain!
slic2: Set pcm->line gain!
slic3: Set hook_min_clr=500ms
slic3: Set hook_min_ko=200ms
slic3: Set hook_max_pd=100ms
slic3: Set hook_dig_interval=200ms
slic3: Set line->pcm gain!
slic3: Set pcm->line gain!
slic4: Set hook_min_clr=500ms
slic4: Set hook_min_ko=200ms
slic4: Set hook_max_pd=100ms
slic4: Set hook_dig_interval=200ms
slic4: Set line->pcm gain!
slic4: Set pcm->line gain!
slic5: Set hook_min_clr=500ms
slic5: Set hook_min_ko=200ms
slic5: Set hook_max_pd=100ms
slic5: Set hook_dig_interval=200ms
slic5: Set line->pcm gain!
slic5: Set pcm->line gain!
slic6: Set hook_min_clr=800ms
slic6: Set hook_min_ko=200ms
slic6: Set hook_max_pd=100ms
slic6: Set hook_dig_interval=200ms
slic6: Set line->pcm gain!
slic6: Set pcm->line gain!
slic7: Set hook_min_clr=500ms
slic7: Set hook_min_ko=200ms
slic7: Set hook_max_pd=100ms
slic7: Set hook_dig_interval=200ms
slic7: Set line->pcm gain!
slic7: Set pcm->line gain!