После отключения питания в доме, перестал загружаться коммутатор MES2324B. При подключении консолью, выдает следующее:
Код: Выделить всё
BootROM 1.41
Booting from SPI flash
General initialization - Version: 1.0.0
Serdes initialization - Version: 1.0.2
PEX: pexIdx 0, detected no link
DDR3 Training Sequence - Ver TIP-1.55.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
Updated Physical Mem size is from 0x20000000 to 10000000
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
Starting U-Boot. Press ctrl+shift+6 to enable debug mode.
Debug mode enabled.
_____ _ _
| ____| | |_ _____ __
| _| | | __/ _ \ \/ /
| |___| | || __/> <
|_____|_|\__\___/_/\_\
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01 (Sep 05 2018 - 12:07:54) Eltex version: 2016_T1.0.eng_drop_v6 4.0.10
mvRolInitParams: mvRolXmodemUsed = 0
mvRolInitParams: mvRolImageaddr = 0x1c000000
mvRolInitParams: mvRolLabMode = 1
Board: ALLEYCAT3-Customer-Board-0
SoC: Alleycat3 Rev A1
running 1 CPUs
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 800 [MHz]
L2 @ 200 [MHz]
TClock @ 200 [MHz]
DDR @ 400 [MHz]
DDR 16Bit Width, FastPath Memory Access, DLB Enabled
DDR ECC Disabled
DRAM: 512 MiB
MTL: boardId = 0 0 1 0
NAND: 512 MiB
SF: Detected MX25L25635E with page size 64 KiB, total 32 MiB
PCI-e 0: Detected No Link.
FPU initialized to Run Fast Mode.
USB2.0 0: Host Mode
Map: Code: 0x1fe5b000:0x1ff8665c
BSS: 0x1ffef46c
Stack: 0x1f94aef0
Heap: 0x1f94b000:0x1fe5b000
U-Boot Environment: 0x00800000:0x00810000 (SPI)
fpga: board_id is 0xf410
SF: Detected MX25L25635E with page size 64 KiB, total 32 MiB
fpga: image 30680 bytes
fpga: reset nCONFIG...
fpga: Ok. Set nCONFIG... Ok
Loading image: ........Successfully loaded!
SF: Detected MX25L25635E with page size 64 KiB, total 32 MiB
Erasing SPI flash....Writing to SPI flash.....done
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | SGMII | 0x00 |
| egiga1 | SGMII | In-Band |
egiga0 [PRIME], egiga1
SF: Detected MX25L25635E with page size 64 KiB, total 32 MiB
Autoboot in 5 seconds...
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000020000000 : "mtd=0"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 262144 bytes (256 KiB)
UBI: logical eraseblock size: 253952 bytes
UBI: smallest flash I/O unit: 4096
UBI: VID header offset: 4096 (aligned 4096)
UBI: data offset: 8192
UBI error: vtbl_check: bad CRC at record 0: 0x7c465fb3, not 0x9d346cfe
UBI error: vtbl_check: bad CRC at record 0: 0x7c465fb3, not 0x9d346cfe
UBI error: process_lvol: both volume tables are corrupted
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error 22
do_rolImage_cmd: start
SF: Detected MX25L25635E with page size 64 KiB, total 32 MiB
Initializing ROL image ...
do UBI mount rootfs
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:rootfs' errno=-19!
UBI mount rootfs FAILED -1
NAND read: device 0 offset 0x400000, size 0x1000
4096 bytes read: OK
Invalid magic found - not loading from NAND
resetting ...
Похоже, что флешке конец. Что с этим делать?