Один из клиентов(sip-trunk) пожаловался на отсутствие слышимости, стали проверять, в шлюз вёл себя как-то странно, интерфейс долго отзывался, в общем решили перезагрузить.
С тех пор шлюз постоянно перезагружается, доходит до некоторого места и ребутится. Пробовали перезалить прошивку, как указано здесь, например - http://kcs.eltex.nsk.ru/articles/147. Не помогло. Пробовали запустится в синг-мод, добавляя init=/bin/sh в конец параметров загрузки, попадали в шел, но через 15 секунд шлюз уходил в ребут. думали может перегрелся, выключили, дали остыть, но это не помогло.
Ниже приведено то что видим на консоли(пара циклов ), так повторяется бесконечно.
Скажите, есть ли надежда реанимировать шлюз удалённо, находится он в другом городе, или тут без вариантов надо его везти в сервис?
Код: Выделить всё
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** BOARD NAME: Eltex PP4X LE
** Linux - LE/BE support
** vxWorks - LE/BE support
U-Boot 1.1.4 (Feb 13 2013 - 10:40:02) Marvell version: 3.3.21-1.1.4_003 LionRD
U-Boot code: 01200000 -> 012AFFF0 BSS: -> 01331050
Soc: MV78200 A1 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=5
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 64bit width
[16384kB@ff000000] Flash: 16 MB
Addresses 85M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (85M - 21M): Done
NAND:nand_scan: maf id: 2C, dev id: 48
NAND parameters: erasesize=0x80000, pagesize=4096, oobsize=224, busw=x8 (0x0)
2048 MB
*** Warning - bad CRC, using default environment
CPU 0: ARM926 (Rev 0)
Streaming enabled
Write allocate disabled
FPU initialized to Run Fast Mode.
USB 0: host mode
USB 1: host mode
USB 2: device mode
Factory settings:
MODEL : <SMG-1016M>
S/N : <VI1F001482>
WAN MAC : <A8:F9:4B:88:79:7C>
LAN MAC : <02:00:04:88:79:7C>
Net: MII INIT
miiphy_register: added 'egiga0', read=0x0124c65c, write=0x0124c64c
miiphy_register: added 'egiga1', read=0x0124c65c, write=0x0124c64c
miiphy_register: added 'egiga2', read=0x0124c65c, write=0x0124c64c
miiphy_register: added 'egiga3', read=0x0124c65c, write=0x0124c64c
egiga0 [PRIME], egiga1, egiga2, egiga3
Detect switch 0: 88e6131 (0x041066) detected. OK
Detect switch 1: 88e6182 (0x041a62) detected. OK
Disable switch 0: ..Ok!
Init phy 1: ..Ok!
Init phy 2: ..Ok!
Autobooting in 3 seconds, press 'stop' for stop
NAND read: device 0 offset 0x0, size 0x500000
5242880 bytes read: OK
NAND read: device 0 offset 0x500000, size 0x2000000
33554432 bytes read: OK
## Booting image at 08000000 ...
Image Name: Linux-2.6.22.18
Created: 2013-11-13 9:47:14 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1988672 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Checking for Linux kernel endianess at 0x08000040 = 0xe1a00000
Linux Kernel is LE
Starting kernel in LE mode ...
Uncompressing Linux..................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18 (bokrenok@lunathris) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #9 Wed Nov 13 16:47:10 NOVT 2013
CPU: ARM926EJ-S [41159260] revision 0 (ARMv5TE), cr=00053977
Machine: Feroceon-MV78XX0
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 130048
DMA zone: 1016 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 129032 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists. Total pages: 129032
Kernel command line: 4 mtdparts=spi_flash:12m(config),2944k(free),128k(factory),1m(uboot);nand_mtd:5m(kernel),32m(initrd),32m(fs),32m(fsupd),512m(disk) mem=508M user_debug=31 ignore_logleve0
debug: ignoring loglevel setting.
IRQ initialize for core 0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 508MB = 508MB total
Memory: 474624KB available (3864K code, 4191K data, 136K init)
Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU 0, CPU Interface
-------------
SDRAM_CS0.... ....base 00000000, size 512MB
SDRAM_CS1.... ....disable
SDRAM_CS2.... ....disable
SDRAM_CS3.... ....disable
DEVICE_CS0... ....base f8000000, size 32MB
DEVICE_CS1... ....base fe000000, size 1MB
DEVICE_CS2... ....base fc000000, size 1MB
DEVICE_CS3... ....no such
DEV_BOOCS.... ....base fb000000, size 8MB
DEVICE_SPI... ....base fb000000, size 8MB
PEX0_IO...... ....no such
PEX0_MEM0.... ....base cc000000, size 64MB
PEX1_IO...... ....no such
PEX1_MEM0.... ....base d0000000, size 64MB
PEX2_IO...... ....no such
PEX2_MEM0.... ....base d4000000, size 64MB
PEX3_IO...... ....no such
PEX3_MEM0.... ....base d8000000, size 64MB
PEX4_IO...... ....no such
PEX4_MEM0.... ....base dc000000, size 64MB
PEX5_IO...... ....no such
PEX5_MEM0.... ....base e0000000, size 64MB
PEX6_IO...... ....no such
PEX6_MEM0.... ....base e4000000, size 64MB
PEX7_IO...... ....no such
PEX7_MEM0.... ....base e8000000, size 64MB
CRYPT_ENG..... ....base f7000000, size 2MB
INTER_REGS... ....base f1000000, size 1MB
MA4000 PP4X Board (LSP Version 2.1.4_MV78XX0) Soc: MV78200 A1 LE
Detected Tclk 200000000 and SysClk 400000000
Marvell USB EHCI Host controller #0: 90c8d600
Marvell USB EHCI Host controller #1: 90c8d400
Marvell USB EHCI Gadget controller #2: 90c8d200
mv_pci_preinit() - start (maxif=8)
mv_pci_preinit: pciIf=0
PEX0 interface detected no Link.
mv_pci_preinit: mvPexInit(0, 0)==13
PCI-E 0: no link - shutdown interface.
mv_pci_preinit: pciIf=1
PEX1 interface detected no Link.
mv_pci_preinit: mvPexInit(1, 0)==13
PCI-E 1: no link - shutdown interface.
mv_pci_preinit: pciIf=2
PEX2 interface detected no Link.
mv_pci_preinit: mvPexInit(2, 0)==13
PCI-E 2: no link - shutdown interface.
mv_pci_preinit: pciIf=3
PEX3 interface detected no Link.
mv_pci_preinit: mvPexInit(3, 0)==13
PCI-E 3: no link - shutdown interface.
mv_pci_preinit: pciIf=4
PEX4 interface detected no Link.
mv_pci_preinit: mvPexInit(4, 0)==13
PCI-E 4: no link - shutdown interface.
mv_pci_preinit: pciIf=5
mv_pci_preinit: (power off)
mv_pci_preinit: pciIf=6
mv_pci_preinit: (power off)
mv_pci_preinit: pciIf=7
mv_pci_preinit: (power off)
mv_pci_preinit() - end
mv_pci_setup - start (nr=0, sys=90c798e0)
mv_pci_setup (1)
mv_pci_setup (2)
mv_pci_setup (6)
PCI0: cc000000..cfffffff
mv_pci_setup - end (OK)
PCI: Scanning bus 0000:00
PCI: Fixups for bus 0000:00
PCI: bus0: Fast back to back transfers enabled
PCI: Bus scan for 0000:00 returning with max=00
mv_pci_setup - start (nr=1, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=2, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=3, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=4, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=5, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=6, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=7, sys=90c79820)
mv_pci_setup - end (powered down)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: orion_clocksource clocksource has been installed.
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 32768K
XOR registered 1 NET_DMA over 2 channels
XOR 2nd invalidate WA enabled
cesadev_init(90011888)
mvCesaInit: sessions=640, queue=64, pSram=f7000000
JFFS2 version 2.2. (NAND) (SUMMARY) é 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 12) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 13) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 65535K size 1024 blocksize
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o LRO support enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o SKB Recycle enabled
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o eth0, ifindex = 1, GbE port = 0
o eth1, ifindex = 2, GbE port = 1
GbE 2 is not mapped to this CPU
GbE 3 is not mapped to this CPU
MV78xxx SMI bus: probed
Ethernet Channel Bonding Driver: v3.2.3 (December 6, 2007)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access 8GB SATA Flash Drive SFDB PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 15744960 512-byte hardware sectors (8061 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 15744960 512-byte hardware sectors (8061 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: unknown partition table
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
SPI Serial flash detected @ 0xfb000000, 16384KB (4096sec x 4KB)
Using static partition definition for spi_flash
Creating 4 MTD partitions on "spi_flash":
0x00000000-0x00400000 : "config"
0x00400000-0x00ee0000 : "free"
0x00ee0000-0x00f00000 : "factory"
0x00f00000-0x01000000 : "uboot"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x48 (Micron NAND 2GiB 3,3V 8-bit)
NAND parameters: erasesize=0x80000, pagesize=4096, oobsize=224, busw=x8 (0x0)
Scanning device for bad blocks
Bad eraseblock 90 at 0x02d00000
Bad eraseblock 91 at 0x02d80000
Using static partition definition for nand_mtd
Creating 6 MTD partitions on "nand_mtd":
0x00000000-0x00500000 : "kernel"
0x00500000-0x02500000 : "initrd"
0x02500000-0x04500000 : "fs"
0x04500000-0x06500000 : "fsupd"
0x06500000-0x06d00000 : "database"
0x06d00000-0x26d00000 : "disk"
usbmon: debugfs is not available
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 16, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_marvell ehci_marvell.168472: Marvell Orion EHCI
ehci_marvell ehci_marvell.168472: new USB bus registered, assigned bus number 2
ehci_marvell ehci_marvell.168472: irq 17, io base 0xf1051100
ehci_marvell ehci_marvell.168472: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
ds1307 1-0068: rtc core: registered ds1307 as rtc0
LM75 thermal sensor detected (bus 0x1, address 0x48)
LM75 thermal sensor detected (bus 0x1, address 0x49)
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[RTP-SW] Inited. RC12 2013-02-02 10:49:51
smg1016m: probe
F BOOT: idle
[smg1016m] load cpld, image 216872 bytes, reset nCONFIG...ok, set nCONFIG...ok, loading: ...........................OK
FPGA version=0x6CB7
smg1016m: switch addr error, write 0x55aa, read 0x57ba
smg1016m: error, can't initialize board!
falc: probe
falc: device-probe
falc: request_irq
No IRQF_TRIGGER set_type function for IRQ 94 (<NULL>)
falc: got irq: 94
falc: pcmdev-init
qfalc_initialize: enter
falc: found QFALC 00, ver. 3.1
falc: not found QFALC 01, ver. 0xC0
falc: not found QFALC 02, ver. 0xC0
falc: not found QFALC 03, ver. 0xC0
falc: inited
pcmex: register device. version: 28.10.2010 17:37:39
pcmex: que-pool init
pcmex: proc init
pcmex: inited
pcmcap: register device.
pcmcap: inited
nf_conntrack version 0.5.0 (4064 buckets, 32512 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
Distributed Switch Architecture driver version 0.1
eth0[0]: detected a Marvell 88E6131 switch
Init PHY at 0x1......OK!
Init PHY at 0x2......OK!
dsa slave smi: probed
dsa: creating CPU interface eth0
dsa: interface with name eth0 already exists
dsa: renaming it to eth0.orig
dsa_char_add: major=235
eth0.orig[1]: detected a Marvell 88E6182 switch
dsa slave smi: probed
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
SCTP: Hash tables configured (established 16384 bind 32768)
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 136K
INIT: version 2.88 booting
Backup rc.d
chgrp: unknown group utmp
Tue Jul 18 19:09:55 GMT+6 2017
Init eth0.orig from rc.sysinit
eth0.orig: started
bonding: bond0: setting mode to 802.3ad (4).
bonding: bond0: Setting MII monitoring interval to 100.
Restore config from flash
/dev/smg1016m: Could not open, err: No such device or address (6)
F boot-state 0
Try restore config...
New image 0
Restored successful
restore: set '/usr/zoneinfo/GMT+3' as local-timezone
Restore rc.d from backup
Applying rc.params
mount fs
install fs
Install filesystem...
SMG1016M detected. Continue
Done.
mount fs_upd
install fs_upd
Install filesystem-update...
SMG1016M detected. Continue
Done.
mount database
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** BOARD NAME: Eltex PP4X LE
** Linux - LE/BE support
** vxWorks - LE/BE support
U-Boot 1.1.4 (Feb 13 2013 - 10:40:02) Marvell version: 3.3.21-1.1.4_003 LionRD
U-Boot code: 01200000 -> 012AFFF0 BSS: -> 01331050
Soc: MV78200 A1 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=5
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 64bit width
[16384kB@ff000000] Flash: 16 MB
Addresses 85M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (85M - 21M): Done
NAND:nand_scan: maf id: 2C, dev id: 48
NAND parameters: erasesize=0x80000, pagesize=4096, oobsize=224, busw=x8 (0x0)
2048 MB
*** Warning - bad CRC, using default environment
CPU 0: ARM926 (Rev 0)
Streaming enabled
Write allocate disabled
FPU initialized to Run Fast Mode.
USB 0: host mode
USB 1: host mode
USB 2: device mode
Factory settings:
MODEL : <SMG-1016M>
S/N : <VI1F001482>
WAN MAC : <A8:F9:4B:88:79:7C>
LAN MAC : <02:00:04:88:79:7C>
Net: MII INIT
miiphy_register: added 'egiga0', read=0x0124c65c, write=0x0124c64c
miiphy_register: added 'egiga1', read=0x0124c65c, write=0x0124c64c
miiphy_register: added 'egiga2', read=0x0124c65c, write=0x0124c64c
miiphy_register: added 'egiga3', read=0x0124c65c, write=0x0124c64c
egiga0 [PRIME], egiga1, egiga2, egiga3
Detect switch 0: 88e6131 (0x041066) detected. OK
Detect switch 1: 88e6182 (0x041a62) detected. OK
Disable switch 0: ..Ok!
Init phy 1: ..Ok!
Init phy 2: ..Ok!
Autobooting in 3 seconds, press 'stop' for stop
NAND read: device 0 offset 0x0, size 0x500000
5242880 bytes read: OK
NAND read: device 0 offset 0x500000, size 0x2000000
33554432 bytes read: OK
## Booting image at 08000000 ...
Image Name: Linux-2.6.22.18
Created: 2013-11-13 9:47:14 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1988672 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Checking for Linux kernel endianess at 0x08000040 = 0xe1a00000
Linux Kernel is LE
Starting kernel in LE mode ...
Uncompressing Linux..................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18 (bokrenok@lunathris) (gcc version 4.3.2 (sdk3.2rc1-ct-ng-1.4.1) ) #9 Wed Nov 13 16:47:10 NOVT 2013
CPU: ARM926EJ-S [41159260] revision 0 (ARMv5TE), cr=00053977
Machine: Feroceon-MV78XX0
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 130048
DMA zone: 1016 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 129032 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists. Total pages: 129032
Kernel command line: 4 mtdparts=spi_flash:12m(config),2944k(free),128k(factory),1m(uboot);nand_mtd:5m(kernel),32m(initrd),32m(fs),32m(fsupd),512m(disk) mem=508M user_debug=31 ignore_logleve0
debug: ignoring loglevel setting.
IRQ initialize for core 0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 508MB = 508MB total
Memory: 474624KB available (3864K code, 4191K data, 136K init)
Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU 0, CPU Interface
-------------
SDRAM_CS0.... ....base 00000000, size 512MB
SDRAM_CS1.... ....disable
SDRAM_CS2.... ....disable
SDRAM_CS3.... ....disable
DEVICE_CS0... ....base f8000000, size 32MB
DEVICE_CS1... ....base fe000000, size 1MB
DEVICE_CS2... ....base fc000000, size 1MB
DEVICE_CS3... ....no such
DEV_BOOCS.... ....base fb000000, size 8MB
DEVICE_SPI... ....base fb000000, size 8MB
PEX0_IO...... ....no such
PEX0_MEM0.... ....base cc000000, size 64MB
PEX1_IO...... ....no such
PEX1_MEM0.... ....base d0000000, size 64MB
PEX2_IO...... ....no such
PEX2_MEM0.... ....base d4000000, size 64MB
PEX3_IO...... ....no such
PEX3_MEM0.... ....base d8000000, size 64MB
PEX4_IO...... ....no such
PEX4_MEM0.... ....base dc000000, size 64MB
PEX5_IO...... ....no such
PEX5_MEM0.... ....base e0000000, size 64MB
PEX6_IO...... ....no such
PEX6_MEM0.... ....base e4000000, size 64MB
PEX7_IO...... ....no such
PEX7_MEM0.... ....base e8000000, size 64MB
CRYPT_ENG..... ....base f7000000, size 2MB
INTER_REGS... ....base f1000000, size 1MB
MA4000 PP4X Board (LSP Version 2.1.4_MV78XX0) Soc: MV78200 A1 LE
Detected Tclk 200000000 and SysClk 400000000
Marvell USB EHCI Host controller #0: 90c8d600
Marvell USB EHCI Host controller #1: 90c8d400
Marvell USB EHCI Gadget controller #2: 90c8d200
mv_pci_preinit() - start (maxif=8)
mv_pci_preinit: pciIf=0
PEX0 interface detected no Link.
mv_pci_preinit: mvPexInit(0, 0)==13
PCI-E 0: no link - shutdown interface.
mv_pci_preinit: pciIf=1
PEX1 interface detected no Link.
mv_pci_preinit: mvPexInit(1, 0)==13
PCI-E 1: no link - shutdown interface.
mv_pci_preinit: pciIf=2
PEX2 interface detected no Link.
mv_pci_preinit: mvPexInit(2, 0)==13
PCI-E 2: no link - shutdown interface.
mv_pci_preinit: pciIf=3
PEX3 interface detected no Link.
mv_pci_preinit: mvPexInit(3, 0)==13
PCI-E 3: no link - shutdown interface.
mv_pci_preinit: pciIf=4
PEX4 interface detected no Link.
mv_pci_preinit: mvPexInit(4, 0)==13
PCI-E 4: no link - shutdown interface.
mv_pci_preinit: pciIf=5
mv_pci_preinit: (power off)
mv_pci_preinit: pciIf=6
mv_pci_preinit: (power off)
mv_pci_preinit: pciIf=7
mv_pci_preinit: (power off)
mv_pci_preinit() - end
mv_pci_setup - start (nr=0, sys=90c798e0)
mv_pci_setup (1)
mv_pci_setup (2)
mv_pci_setup (6)
PCI0: cc000000..cfffffff
mv_pci_setup - end (OK)
PCI: Scanning bus 0000:00
PCI: Fixups for bus 0000:00
PCI: bus0: Fast back to back transfers enabled
PCI: Bus scan for 0000:00 returning with max=00
mv_pci_setup - start (nr=1, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=2, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=3, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=4, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=5, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=6, sys=90c79820)
mv_pci_setup - end (powered down)
mv_pci_setup - start (nr=7, sys=90c79820)
mv_pci_setup - end (powered down)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: orion_clocksource clocksource has been installed.
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 32768K
XOR registered 1 NET_DMA over 2 channels
XOR 2nd invalidate WA enabled
cesadev_init(90011888)
mvCesaInit: sessions=640, queue=64, pSram=f7000000
JFFS2 version 2.2. (NAND) (SUMMARY) é 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 12) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 13) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 65535K size 1024 blocksize
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o LRO support enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o SKB Recycle enabled
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o eth0, ifindex = 1, GbE port = 0
o eth1, ifindex = 2, GbE port = 1
GbE 2 is not mapped to this CPU
GbE 3 is not mapped to this CPU
MV78xxx SMI bus: probed
Ethernet Channel Bonding Driver: v3.2.3 (December 6, 2007)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access 8GB SATA Flash Drive SFDB PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 15744960 512-byte hardware sectors (8061 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 15744960 512-byte hardware sectors (8061 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: unknown partition table
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
SPI Serial flash detected @ 0xfb000000, 16384KB (4096sec x 4KB)
Using static partition definition for spi_flash
Creating 4 MTD partitions on "spi_flash":
0x00000000-0x00400000 : "config"
0x00400000-0x00ee0000 : "free"
0x00ee0000-0x00f00000 : "factory"
0x00f00000-0x01000000 : "uboot"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x48 (Micron NAND 2GiB 3,3V 8-bit)
NAND parameters: erasesize=0x80000, pagesize=4096, oobsize=224, busw=x8 (0x0)
Scanning device for bad blocks
Bad eraseblock 90 at 0x02d00000
Bad eraseblock 91 at 0x02d80000
Using static partition definition for nand_mtd
Creating 6 MTD partitions on "nand_mtd":
0x00000000-0x00500000 : "kernel"
0x00500000-0x02500000 : "initrd"
0x02500000-0x04500000 : "fs"
0x04500000-0x06500000 : "fsupd"
0x06500000-0x06d00000 : "database"
0x06d00000-0x26d00000 : "disk"
usbmon: debugfs is not available
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 16, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_marvell ehci_marvell.168472: Marvell Orion EHCI
ehci_marvell ehci_marvell.168472: new USB bus registered, assigned bus number 2
ehci_marvell ehci_marvell.168472: irq 17, io base 0xf1051100
ehci_marvell ehci_marvell.168472: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
ds1307 1-0068: rtc core: registered ds1307 as rtc0
LM75 thermal sensor detected (bus 0x1, address 0x48)
LM75 thermal sensor detected (bus 0x1, address 0x49)
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[RTP-SW] Inited. RC12 2013-02-02 10:49:51
smg1016m: probe
F BOOT: idle
[smg1016m] load cpld, image 216872 bytes, reset nCONFIG...ok, set nCONFIG...ok, loading: ...........................OK
FPGA version=0x6CB7
smg1016m: switch addr error, write 0x55aa, read 0x57ba
smg1016m: error, can't initialize board!
falc: probe
falc: device-probe
falc: request_irq
No IRQF_TRIGGER set_type function for IRQ 94 (<NULL>)
falc: got irq: 94
falc: pcmdev-init
qfalc_initialize: enter
falc: found QFALC 00, ver. 3.1
falc: not found QFALC 01, ver. 0xC0
falc: not found QFALC 02, ver. 0xC0
falc: not found QFALC 03, ver. 0xC0
falc: inited
pcmex: register device. version: 28.10.2010 17:37:39
pcmex: que-pool init
pcmex: proc init
pcmex: inited
pcmcap: register device.
pcmcap: inited
nf_conntrack version 0.5.0 (4064 buckets, 32512 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
Distributed Switch Architecture driver version 0.1
eth0[0]: detected a Marvell 88E6131 switch
Init PHY at 0x1......OK!
Init PHY at 0x2......OK!
dsa slave smi: probed
dsa: creating CPU interface eth0
dsa: interface with name eth0 already exists
dsa: renaming it to eth0.orig
dsa_char_add: major=235
eth0.orig[1]: detected a Marvell 88E6182 switch
dsa slave smi: probed
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
SCTP: Hash tables configured (established 16384 bind 32768)
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 136K
INIT: version 2.88 booting
Backup rc.d
chgrp: unknown group utmp
Tue Jul 18 19:11:07 GMT+6 2017
Init eth0.orig from rc.sysinit
eth0.orig: started
bonding: bond0: setting mode to 802.3ad (4).
bonding: bond0: Setting MII monitoring interval to 100.
Restore config from flash
/dev/smg1016m: Could not open, err: No such device or address (6)
F boot-state 0
Try restore config...
New image 0
Restored successful
restore: set '/usr/zoneinfo/GMT+3' as local-timezone
Restore rc.d from backup
Applying rc.params
mount fs
install fs
Install filesystem...
SMG1016M detected. Continue
Done.
mount fs_upd
install fs_upd
Install filesystem-update...
SMG1016M detected. Continue
Done.
mount database
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** BOARD NAME: Eltex PP4X LE
** Linux - LE/BE support
** vxWorks - LE/BE support