=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.12.13 09:22:31 =~=~=~=~=~=~=~=~=~=~=~=
  


U-Boot 1.1.6-g26863528-dirty (Apr 22 2015 - 10:43:30) Mindspeed 0.06.2-candidate1


DRAM:  64 MB

Comcerto Flash Subsystem Initialization

check am29gl512: manuf f620, id1=e59f, id2=da02, id3=e28d

check am29gl512: manuf 0001, id1=227e, id2=2223, id3=2201

found am29gl512 flash at B8000000

Flash: 64 MB

NAND:  No NAND device found!!!

0 MiB

In:    serial

Out:   serial

Err:   serial

Reserve MSP memory

Net:   comcerto_gemac0, comcerto_gemac1

Product Id: 106 (88E6131). Rev: 6

Disable switch: ..Ok!

Init phy 1: ..Ok!

Init phy 2: ..Ok!

Autobooting in 3 seconds, press 'stop' for stop

Factory settings:

	Model: TAU-72.IP_AC

	Serial number: VI28002299

	WAN MAC: A8:F9:4B:11:75:47

## Using MAC: A8:F9:4B:11:75:47

## No elf image at address 0xb8300000

## Downloading image at b8300000 ...

code_offset=0x80

code_base=100

data_offset=178

code_size=f8

data_base=1f8

data_size=0

zeroinit_base=1f8

prog_entry=100

 

AIFHEADER:

BL_DecompressCode=e1a00000

BL_SelfRelocCode=e1a00000

BL_DbgInitZeroInit=eb00000c

EntryPointOffset=0

ProgramExitInstr=ef000011

ImageReadOnlySize=f8

ImageReadWriteSize=0

ImageDebugSize=158c

ImageZeroInitSize=0

ImageDebugType=158c1

ImageBase=100

WorkSpace=0

AddressMode=20

DataBase=0

FirstFatOffset=1704

Reserved2=1c2658

DebugInitInstr=e1a00000

ZeroInitCode[0]=e04ec00f

data section size 0

## No elf image at address 0x02000000

Copying ARM1 startup code from 03e00600, start address 02000000


Starting kernel ...


Uncompressing Linux......................................................................................... done, booting the kernel.
Linux version 2.6.22.19-4.03.0-c300evm (jenkins@build) (gcc version 3.4.5) #312 Mon Aug 13 13:51:16 NOVT 2018
CPU: ARMv6-compatible processor [4117b361] revision 1 (ARMv6TEJ), cr=00c5387f
Machine: Comcerto 300 (x570)
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 11938
Kernel command line: setenv bootargs ram=120M console=ttyS0,115200 root=/dev/mtdblock5 ro rootfstype=jffs2 user_debug=31 init=/sbin/restore2
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 47MB = 47MB total
Memory: 44500KB available (2476K code, 530K data, 116K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Comcerto GPIO(s):
0(out=0)
1(in =1)
2(out=0)
3(in =0)
4(out=0)
9(out=0)
22(irq=39, type=1, trigger=0)
Time: timer3 clocksource has been installed.
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
msp-driver: version 0.1
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
cyclone: image 45684 bytes, reset nCONFIG... ok, set nCONFIG... ok
         loading: ............OK
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
nbd: registered device at major 43
m825xx_ved: version 0.0.5-2.6
m825xx_ved: init SMI
gem0: Comcerto Ethernet Controller  02:00:00:00:00:00 
gem1: Comcerto Ethernet Controller  02:00:00:00:00:01 
Comcerto MDIO Bus: probed
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
physmap platform flash device: 04000000 at b8000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 8 MTD partitions on "physmap-flash.0":
0x00000000-0x00040000 : "nor boot"
0x00040000-0x00060000 : "nor boot env"
0x00060000-0x00160000 : "nor config"
0x00160000-0x00300000 : "nor csp"
0x00300000-0x00700000 : "nor msp"
0x00700000-0x01700000 : "root fs"
0x01700000-0x01a00000 : "extend fs"
0x01a00000-0x04000000 : "extra extend fs"
No NAND device found!!!
fxs72: init board
fxs72: board id 0x13
fxs72: (hio) testing memory Ok!
fxs72: inited
SWITCH ID: 1066
fxs72: set state for restart ARM7, read=128

fxs72: restart ARM7, read=0
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (376 buckets, 3008 max)
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
Distributed Switch Architecture driver version 0.1
eth2[0]: detected a Marvell 88E6131 switch
before ATU flush:
ATU dump (DBNum=0):
[G]FF:FF:FF:FF:FF:FF ATUData=0000 (T=0, PortVec=00, EntryState=0 - invalid)
after ATU flush:
ATU dump (DBNum=0):
[G]FF:FF:FF:FF:FF:FF ATUData=0000 (T=0, PortVec=00, EntryState=0 - invalid)
dsa slave smi: probed
create slave dev p0
create slave dev p1
create slave dev p2
create slave dev p4
create slave dev p6
create slave dev p7
dsa: creating CPU interface p5
dsa_char_add: major=235
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
JFFS2 error: (1) jffs2_build_inode_pass1: child dir "bin" (ino #505) of dir ino #478 appears to be a hard link
JFFS2 error: (1) jffs2_build_inode_pass1: child dir "lib" (ino #507) of dir ino #478 appears to be a hard link
JFFS2 error: (1) jffs2_build_inode_pass1: child dir "bin" (ino #508) of dir ino #481 appears to be a hard link
JFFS2 error: (1) jffs2_build_inode_pass1: child dir "version" (ino #538) of dir ino #511 appears to be a hard link
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing init memory: 116K
Failed to execute /sbin/restore2.  Attempting defaults...
Kernel panic - not syncing: No init found.  Try passing init= option to kernel.
