Элтекс

Не могу найти команды для просмотра состояния SFP трансивера (например его тип, температуру, если это DDM, итд)

В свичах SNR это просто показывается вместе с sh interface:

Код: Выделить всё

Interface brief:
  Ethernet1/10 is up, line protocol is up
  Ethernet1/10 is layer 2 port, alias name is link-es1, index is 10
  Hardware is Gigabit-Combo, active is Fiber, address is f8-f0-82-10-34-0d
  PVID is 1
  MTU 9800 bytes, BW 1000000 Kbit
  Time since last status change:0w-2d-9h-28m-59s  (206939 seconds)
  Encapsulation ARPA, Loopback not set
  Auto-duplex: Negotiation full-duplex, Auto-speed: Negotiation 1G bits
  FlowControl is off, MDI type is auto
Transceiver info:
  SFP found in this port, manufactured by CL, on Oct 03 2011.
  Type is 1000BASE-LX.  Serial number is B718080438.
  Link length is 10000 m for Single Mode Fiber.
  Nominal bit rate is 1300 Mb/s.
  Laser wavelength is 1310 nm.
Statistics:
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 556 bits/sec, 1 packets/sec
  The last 5 second input rate 0 bits/sec, 0 packets/sec
  The last 5 second output rate 1110 bits/sec, 1 packets/sec
  Input packets statistics:
    85636 input packets, 8609324 bytes, 0 no buffer
    67236 unicast packets, 12601 multicast packets, 5799 broadcast packets
    0 input errors, 0 CRC, 0 frame alignment, 0 overrun, 0 ignored,
    0 abort, 0 length error, 0 undersize 0 jabber, 0 fragments, 0 pause frame
  Output packets statistics:
    189965 output packets, 15892452 bytes, 0 underruns
    5056 unicast packets, 77054 multicast packets, 107855 broadcast packets
    0 output errors, 0 collisions, 0 late collisions, 0 pause frame

А на этом свиче ничего даже отдаленно напоминающего не нашел:

Код: Выделить всё

#sh interfaces GigabitEthernet 1/0/28
gigabitethernet 1/0/28 is down (not connected)
  Interface index is 76
  Hardware is gigabitethernet, MAC address is a8:f9:4b:8c:e0:dc
  Description: fiber-e6
  Interface MTU is 10218
  Port is down
  Flow control is off, MDIX mode is unknown
  15 second input rate is 0 Kbit/s
  15 second output rate is 0 Kbit/s
      0 packets input, 0 bytes received
      0 broadcasts, 0 multicasts
      0 input errors, 0 FCS, 0 alignment
      0 oversize, 0 internal MAC
      0 pause frames received
      0 packets output, 0 bytes sent
      0 broadcasts, 0 multicasts
      0 output errors, 0 collisions
      0 excessive collisions, 0 late collisions
      0 pause frames transmitted
      0 symbol errors, 0 carrier, 0 SQE test error

Код: Выделить всё

#show fiber-ports optical-transceiver detailed interface GigabitEthernet0/10

   Port      Temp  Voltage Current  Output        Input        LOS  Transceiver
             [C]   [V]     [mA]     Power         Power             Type
                                    [mW / dBm]    [mW / dBm]
----------- ------ ------- ------- ------------- ------------- --- -------------
 gi1/0/10     44    3.31    11.57  0.27 / -5.59  0.01 / -17.30 No      Fiber

 Temp         - Internally measured transceiver temperature
 Voltage      - Internally measured supply voltage
 Current      - Measured TX bias current
 Output Power - Measured TX output power in milliWatts/dBm
 Input Power  - Measured RX received power in milliWatts/dBm
 LOS          - Loss of signal
 N/A - Not Available, N/S - Not Supported, W - Warning, E - Error

        Transceiver information:
Vendor name: OptiCin
Serial number: YF73560015
Connector type: LC
Type: SFP/SFP+
Compliance code: 1000BASE-LX
Laser wavelength: 1310 nm
Transfer distance: 20000 m
Diagnostic: supported

Элтекс

mes2124M как посмотреть тип SFP трансивера

mes2124M как посмотреть тип SFP трансивера

Re: mes2124M как посмотреть тип SFP трансивера