Элтекс

производство оборудования для телекоммуникаций
http://forum.eltex-co.ru/

MultiWan и esr-10

http://forum.eltex-co.ru/viewtopic.php?f=10&t=7506

Страница 1 из 1

MultiWan и esr-10

Добавлено: 19 июл 2017 10:38
AlexanderV
Добрый день, согласно инструкции с сайта пытаюсь настроить резервирование канала на ESR-10, решил использовать для этого функционал MultiWan и... потерпел неудачу
на роутере настроен cнат, основной аплинк получает адрес по дхцп резервный имеет статический адрес. никаких статически маршрутов нет. Внутрь сети смотрит один бридж, наружу два бриджа 20 и 21.
настроен нат так:
nat source
ruleset SNAT
to zone UPLINK
rule 10
match protocol any
match source-address any
match destination-address any
action source-nat interface
enable
exit
exit
exit

сам multiwan
настраивал так:

Код: Выделить всё

2017-07-18T20:06:31+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: ip route 0.0.0.0/0 wan load-balance rule 1
2017-07-18T20:06:47+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance rule 1
2017-07-18T20:07:13+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: outbound interface bridge 20
2017-07-18T20:07:18+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: outbound interface bridge 21
2017-07-18T20:07:26+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: enable
2017-07-18T20:07:33+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:07:46+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance target-list GOOGLE
2017-07-18T20:07:52+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: target 1
2017-07-18T20:08:05+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: ip address 8.8.8.8
2017-07-18T20:08:09+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: enable
2017-07-18T20:08:11+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:08:20+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:08:35+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: bridge 20
2017-07-18T20:09:05+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance nexthop 1.1.1.1
2017-07-18T20:09:14+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance target-list GOOGLE
2017-07-18T20:09:25+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance enable
2017-07-18T20:09:29+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:09:45+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: bridge 21
2017-07-18T20:10:00+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance nexthop 2.2.2.2
2017-07-18T20:10:11+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance target-list GOOGLE
2017-07-18T20:10:21+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance enable
2017-07-18T20:10:27+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:10:36+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance rule 1
2017-07-18T20:10:46+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: failover
2017-07-18T20:10:58+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:12:54+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: bridge 20
2017-07-18T20:13:04+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance nexthop dhcp enable  !здесь я вспомнил что у меня ж дхцп на основном аплинке и добавил строчку про дхцп
2017-07-18T20:14:09+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: exit
2017-07-18T20:14:11+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: wan load-balance rule 1
2017-07-18T20:14:48+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: outbound interface bridge 20 1
2017-07-18T20:14:54+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: outbound interface bridge 21 10
2017-07-18T20:14:57+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: end
2017-07-18T20:15:50+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: show candidate-config
2017-07-18T20:16:01+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: configure
2017-07-18T20:16:03+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: bridge 11
2017-07-18T20:16:27+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: no ip policy route-map
2017-07-18T20:16:28+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: end
2017-07-18T20:16:53+07:00 <global_event_wait_try> (/config_applied)
2017-07-18T20:16:53+07:00 <global_event_wait_try> after wait (/config_applied), rc = 0
2017-07-18T20:16:53+07:00 %WAN-I-INSTANCE: IP interface bridge 20 changed state to inactive
2017-07-18T20:16:53+07:00 %WAN-I-INSTANCE: IP interface bridge 21 changed state to inactive
2017-07-18T20:16:53+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:16:53+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:16:53+07:00 Wrote 0 class decls to leases file.
2017-07-18T20:16:53+07:00 Wrote 99 leases to leases file.
2017-07-18T20:16:53+07:00 %CLI-I-CRIT: user admin from ssh 10.10.0.42 input: commit

после коммита связь не сломалась и я выдернул основной аплинк (gigabitethernet 1/0/4) ожидая что трафик пойдёт через резервный (gigabitethernet 1/0/3)
но связь не появилась в логах были такие надписи

Код: Выделить всё

2017-07-18T20:16:53+07:00 Server starting service.
2017-07-18T20:16:58+07:00 %WAN-I-INSTANCE: IP interface bridge 21 last check target 8.8.8.8 success
2017-07-18T20:16:58+07:00 %WAN-I-INSTANCE: IP interface bridge 21 changed state to active
2017-07-18T20:17:00+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:00+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:06+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:06+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:12+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:12+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:18+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:18+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:24+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:24+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:30+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:30+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:37+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:37+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:43+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:43+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:49+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:49+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:17:55+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:17:55+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:01+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:01+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:04+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: show candidate-config
2017-07-18T20:18:07+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:07+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:14+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:14+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:20+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:20+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:26+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:26+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:32+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:32+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:38+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:38+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:45+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:45+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:51+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:51+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:18:57+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:18:57+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:03+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:03+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:09+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:09+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:15+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:15+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:17+07:00 %LINK-W-DOWN: gigabitethernet 1/0/4 changed state to down
2017-07-18T20:19:22+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:22+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:28+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:28+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:34+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:34+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:40+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:40+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:46+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:46+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:52+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:52+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:19:59+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:19:59+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:20:03+07:00 %LINK-I-UP: gigabitethernet 1/0/4 changed state to up, speed 100M, full-duplex
2017-07-18T20:20:05+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:20:05+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:20:11+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:20:11+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:20:17+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:20:17+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:20:23+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:20:23+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:20:29+07:00 %WAN-W-ERR: <check_arp_exist> Inet_aton
2017-07-18T20:20:29+07:00 wan_lb: error on sending icmp packet: 0
2017-07-18T20:20:31+07:00 <global_event_wait_try> (/config_applied)
2017-07-18T20:20:31+07:00 <global_event_wait_try> after wait (/config_applied), rc = 0
2017-07-18T20:20:31+07:00 Wrote 0 class decls to leases file.
2017-07-18T20:20:31+07:00 Wrote 99 leases to leases file.
2017-07-18T20:20:31+07:00 Server starting service.
2017-07-18T20:20:31+07:00 %CLI-I-CMD: user admin from ssh 10.10.0.42 input: restore


что я сделал не так? как заставить фичу работать?

Re: MultiWan и esr-10

Добавлено: 31 июл 2017 14:32
leonid_zarkov
Александр, проблема именно в маршруте от DHCP, проблема решается в версии ПО 1.4.0 (релиз ожидается осенью текущего года).
Часовой пояс: UTC+07:00
Страница 1 из 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/