Прошивка MXL

[rus30]

Прошили MXL новой прошивкой и нет ответа от него.Терминал показывает что он постоянно перегружается.Пробывал шить через TFTP сервер появляется строка загрузки и далее TTTTTTTT
что может бать.

Лог терминала прилагаю
## Booting image at 20080000 ...
Image Name: MXL Firmware Image
Created: 2009-07-24 3:51:17 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 2894575 Bytes = 2.8 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.12.1-BFIN-2005R4 #699 Fri Jul 24 10:50:19 NOVST 2009
Blackfin support (C) 2004 Analog Devices, Inc.
ADSP-BF537 Rev. 0.2
uClinux/BF537
Blackfin uClinux support by blackfin.uclinux.org
Processor Speed: 589 MHz core clock and 117 Mhz System Clock
Board Memory: 32MB
Memory map:
text = 0x001000-0x134d54
data = 0x1418ec-0x185724
bss = 0x185730-0x1b06f8
rootfs = 0x1a00000-0x1f00000
stack = 0x142000-0x144000
Command line: 'root=/dev/mtdblock3 rw'
Instruction Cache Enabled
Data Cache Enabled (write-back)
Hardware Trace Enabled
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3 rw
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Physical pages: 1a00
Memory available: 24620k/31481k RAM, (49k init code, 1231k kernel code, 443k dat
a, 6144k dma)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin DATA_A SRAM: 16 KB
Blackfin DATA_B SRAM: 16 KB
Mount-cache hash table entries: 512
NET: Registered protocol family 16
stamp_init(): registering device resources
Real Time Clock Driver v1.10e
BlackFin BF533 serial driver version 2.00 With DMA Support
io scheduler noop registered
io scheduler cfq registered
Blackfin 537 mac net device registered.
BF5xx flash: probing 16-bit flash bus
Found: AMD AM29LV320DB
BF5xx flash: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using static partition definition
Creating 3 MTD partitions on "BF5xx flash":
0x00000000-0x00060000 : "Bootloader"
0x00060000-0x00080000 : "Params"
0x00080000-0x00400000 : "uClinux"
uclinux[mtd]: RAM probe address=0x1a00000 size=0x500000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00500000 : "EXT2fs"
uclinux[mtd3]: set EXT2fs to be root filesystem
tmr: driver initialized, max timers count = 4
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
board: couldn't upload device!



U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
## Booting image at 20080000 ...
Image Name: MXL Firmware Image
Created: 2009-07-24 3:51:17 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 2894575 Bytes = 2.8 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.12.1-BFIN-2005R4 #699 Fri Jul 24 10:50:19 NOVST 2009
Blackfin support (C) 2004 Analog Devices, Inc.
ADSP-BF537 Rev. 0.2
uClinux/BF537
Blackfin uClinux support by blackfin.uclinux.org
Processor Speed: 589 MHz core clock and 117 Mhz System Clock
Board Memory: 32MB
Memory map:
text = 0x001000-0x134d54
data = 0x1418ec-0x185724
bss = 0x185730-0x1b06f8
rootfs = 0x1a00000-0x1f00000
stack = 0x142000-0x144000
Command line: 'root=/dev/mtdblock3 rw'
Instruction Cache Enabled
Data Cache Enabled (write-back)
Hardware Trace Enabled
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3 rw
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Physical pages: 1a00
Memory available: 24620k/31481k RAM, (49k init code, 1231k kernel code, 443k dat
a, 6144k dma)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin DATA_A SRAM: 16 KB
Blackfin DATA_B SRAM: 16 KB
Mount-cache hash table entries: 512
NET: Registered protocol family 16
stamp_init(): registering device resources
Real Time Clock Driver v1.10e
BlackFin BF533 serial driver version 2.00 With DMA Support
io scheduler noop registered
io scheduler cfq registered
Blackfin 537 mac net device registered.
BF5xx flash: probing 16-bit flash bus
Found: AMD AM29LV320DB
BF5xx flash: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using static partition definition
Creating 3 MTD partitions on "BF5xx flash":
0x00000000-0x00060000 : "Bootloader"
0x00060000-0x00080000 : "Params"
0x00080000-0x00400000 : "uClinux"
uclinux[mtd]: RAM probe address=0x1a00000 size=0x500000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00500000 : "EXT2fs"
uclinux[mtd3]: set EXT2fs to be root filesystem
tmr: driver initialized, max timers count = 4
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
board: couldn't upload device!



U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr192.168.1.2
bf537> set serverip192.168.1.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'File not found' (1)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'File not found' (1)
Starting again

U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr192.168.1.2
bf537> set serverip192.168.1.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'File not found' (1)
Starting again

U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr192.168.1.2
bf537> set serverip192.168.1.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
## Booting image at 20080000 ...
Image Name: MXL Firmware Image
Created: 2009-07-24 3:51:17 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 2894575 Bytes = 2.8 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.12.1-BFIN-2005R4 #699 Fri Jul 24 10:50:19 NOVST 2009
Blackfin support (C) 2004 Analog Devices, Inc.
ADSP-BF537 Rev. 0.2
uClinux/BF537
Blackfin uClinux support by blackfin.uclinux.org
Processor Speed: 589 MHz core clock and 117 Mhz System Clock
Board Memory: 32MB
Memory map:
text = 0x001000-0x134d54
data = 0x1418ec-0x185724
bss = 0x185730-0x1b06f8
rootfs = 0x1a00000-0x1f00000
stack = 0x142000-0x144000
Command line: 'root=/dev/mtdblock3 rw'
Instruction Cache Enabled
Data Cache Enabled (write-back)
Hardware Trace Enabled
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3 rw
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Physical pages: 1a00
Memory available: 24620k/31481k RAM, (49k init code, 1231k kernel code, 443k dat
a, 6144k dma)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin DATA_A SRAM: 16 KB
Blackfin DATA_B SRAM: 16 KB
Mount-cache hash table entries: 512
NET: Registered protocol family 16
stamp_init(): registering device resources
Real Time Clock Driver v1.10e
BlackFin BF533 serial driver version 2.00 With DMA Support
io scheduler noop registered
io scheduler cfq registered
Blackfin 537 mac net device registered.
BF5xx flash: probing 16-bit flash bus
Found: AMD AM29LV320DB
BF5xx flash: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using static partition definition
Creating 3 MTD partitions on "BF5xx flash":
0x00000000-0x00060000 : "Bootloader"
0x00060000-0x00080000 : "Params"
0x00080000-0x00400000 : "uClinux"
uclinux[mtd]: RAM probe address=0x1a00000 size=0x500000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00500000 : "EXT2fs"
uclinux[mtd3]: set EXT2fs to be root filesystem
tmr: driver initialized, max timers count = 4
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
board: couldn't upload device!



U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
## Booting image at 20080000 ...
Image Name: MXL Firmware Image
Created: 2009-07-24 3:51:17 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 2894575 Bytes = 2.8 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.12.1-BFIN-2005R4 #699 Fri Jul 24 10:50:19 NOVST 2009
Blackfin support (C) 2004 Analog Devices, Inc.
ADSP-BF537 Rev. 0.2
uClinux/BF537
Blackfin uClinux support by blackfin.uclinux.org
Processor Speed: 589 MHz core clock and 117 Mhz System Clock
Board Memory: 32MB
Memory map:
text = 0x001000-0x134d54
data = 0x1418ec-0x185724
bss = 0x185730-0x1b06f8
rootfs = 0x1a00000-0x1f00000
stack = 0x142000-0x144000
Command line: 'root=/dev/mtdblock3 rw'
Instruction Cache Enabled
Data Cache Enabled (write-back)
Hardware Trace Enabled
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3 rw
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Physical pages: 1a00
Memory available: 24620k/31481k RAM, (49k init code, 1231k kernel code, 443k dat
a, 6144k dma)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin DATA_A SRAM: 16 KB
Blackfin DATA_B SRAM: 16 KB
Mount-cache hash table entries: 512
NET: Registered protocol family 16
stamp_init(): registering device resources
Real Time Clock Driver v1.10e
BlackFin BF533 serial driver version 2.00 With DMA Support
io scheduler noop registered
io scheduler cfq registered
Blackfin 537 mac net device registered.
BF5xx flash: probing 16-bit flash bus
Found: AMD AM29LV320DB
BF5xx flash: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using static partition definition
Creating 3 MTD partitions on "BF5xx flash":
0x00000000-0x00060000 : "Bootloader"
0x00060000-0x00080000 : "Params"
0x00080000-0x00400000 : "uClinux"
uclinux[mtd]: RAM probe address=0x1a00000 size=0x500000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00500000 : "EXT2fs"
uclinux[mtd3]: set EXT2fs to be root filesystem
tmr: driver initialized, max timers count = 4
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
board: couldn't upload device!



U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
## Booting image at 20080000 ...
Image Name: MXL Firmware Image
Created: 2009-07-24 3:51:17 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 2894575 Bytes = 2.8 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 1000
Linux version 2.6.12.1-BFIN-2005R4 #699 Fri Jul 24 10:50:19 NOVST 2009
Blackfin support (C) 2004 Analog Devices, Inc.
ADSP-BF537 Rev. 0.2
uClinux/BF537
Blackfin uClinux support by blackfin.uclinux.org
Processor Speed: 589 MHz core clock and 117 Mhz System Clock
Board Memory: 32MB
Memory map:
text = 0x001000-0x134d54
data = 0x1418ec-0x185724
bss = 0x185730-0x1b06f8
rootfs = 0x1a00000-0x1f00000
stack = 0x142000-0x144000
Command line: 'root=/dev/mtdblock3 rw'
Instruction Cache Enabled
Data Cache Enabled (write-back)
Hardware Trace Enabled
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3 rw
Configuring Blackfin Priority Driven Interrupts
PID hash table entries: 128 (order: 7, 2048 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Physical pages: 1a00
Memory available: 24620k/31481k RAM, (49k init code, 1231k kernel code, 443k dat
a, 6144k dma)
Blackfin Scratchpad data SRAM: 4 KB
Blackfin DATA_A SRAM: 16 KB
Blackfin DATA_B SRAM: 16 KB
Mount-cache hash table entries: 512
NET: Registered protocol family 16
stamp_init(): registering device resources
Real Time Clock Driver v1.10e
BlackFin BF533 serial driver version 2.00 With DMA Support
io scheduler noop registered
io scheduler cfq registered
Blackfin 537 mac net device registered.
BF5xx flash: probing 16-bit flash bus
Found: AMD AM29LV320DB
BF5xx flash: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using static partition definition
Creating 3 MTD partitions on "BF5xx flash":
0x00000000-0x00060000 : "Bootloader"
0x00060000-0x00080000 : "Params"
0x00080000-0x00400000 : "uClinux"
uclinux[mtd]: RAM probe address=0x1a00000 size=0x500000
Creating 1 MTD partitions on "RAM":
0x00000000-0x00500000 : "EXT2fs"
uclinux[mtd3]: set EXT2fs to be root filesystem
tmr: driver initialized, max timers count = 4
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
board: couldn't upload device!



U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 2

Прошивали это устройства этой прошивкой uImageMXL1

[AE]

Добрый день.

Судя по логу у вас две проблемы.
Первая - это то, что версия прошивки не соответствует аппаратной версии устройства.
Об этом можно судить по сообщениям о невозможности инициализировать устройство:
PLD (80977 bytes): reset nCONFIG... OK, set nCONFIG... OK, loading... fail!
board: couldn't upload device!


Вторая проблема - в настройке TFTP сервера.
Судя по сообщениям в логе, либо на сервер не помещен файл прошивки, либо сервер настроен только на прием данных, но не на передачу. Замечу только, что правильная настройка TFTP сервера не решила бы общую проблему в связи с наличием проблемы номер один.

Сообщите, пожалуйста, следующее:
- версию вашего устройства (наименование модели);
- контактную информацию для отправки ПО;
- в связи с чем возникла необходимость смены ПО;
- каким путем к вам попала эта прошивка;

Александр

[rus30]

версию вашего устройства (MXL-2)2.6.12.1 2005 jul 31;
- контактную информацию для отправки ПО;-rus30adm@rambler.ru
- в связи с чем возникла необходимость смены ПО;- незнаю,прошивал не я мне уже отдали на востановление.
- каким путем к вам попала эта прошивка;- говорят с ftp посоветовали скачать.

[Прокопьев Максим]

Версия ПО для устройства отправлена в Ваш адрес.

Возникшая трудность при смене ПО через TFTP сервер скорее всего связана с тем, что имя файла прошивки не соответствует имени файла, который ожидает MXL:

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'File not found' (1)
Starting again

ожидается файл с именем uImage, а у Вас файл с именем uImageMXL1

[rus30]

Нехочет шится.Как посмотреть IP адрес при таком состоянии возможно ли.Может IP адрес переписан.


U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 2
U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr192.168.0.2
bf537> set serverip192.168.0.3
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: T T
U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr192.168.1.2
bf537> set serverip192.1681.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)


Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: *
TFTP error: 'TFTP Server Error: server is configured for receive only' (2)
Starting again

[Прокопьев Максим]

Похоже, что TFTP сервер настроен только на прием (было описано выше). Каким TFTP сервером пользуетесь?

[rus30]

SolarWinds-TFTP-Server и tftpd32

[Прокопьев Максим]

воспользуйтесь tftpd32 и установите настройки по умолчанию

[rus30]

Тоже самое,настройки сбросил.

U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr192.168.0.2
bf537> set serverip192.168.0.3
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2
Filename 'uImage'.
Load address: 0x1000
Loading: T T

[Женя]

Обратите внимание на правильность ввода команд:

bf537> set ipaddr192.168.0.2
bf537> set serverip192.168.0.3
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.1.9; our IP address is 192.168.1.2

после ipaddr и serverip нужно поставить пробел
set ipaddr 192.168.0.2
set serverip 192.168.0.3

еще введите команду print и выложите все что выдаст устройство

[rus30]

Вроде прошился а работать нехочет выкладываю логи
1 при прошивке
2 загрузка
U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr 192.168.0.2
bf537> set serverip 192.168.0.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.0.9; our IP address is 192.168.0.2
Filename 'uImage'.
Load address: 0x1000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 2947077 (2cf805 hex)

Erasing Flash locations, Please Wait
........................................
Erased 40 sectors
Copy to Flash... Flash not erased at offset 0x300000
done
bf537> print
bootargs=root=/dev/mtdblock3 rw
bootcmd=run flashboot
bootdelay=2
baudrate=57600
loads_echo=1
ethaddr=02:80:ad:20:31:b8
autoload=no
rootpath=/romfs
hostname=BF537
flashboot=bootm 0x20080000
ramboot=tftp 0x01A00000 uImage;bootm;
update=tftp 0x1000 u-boot.bin;protect off 0x20000000 0x2002FFFF;erase 0x20000000
0x2002FFFF;cp.b 0x1000 0x20000000 $(filesize);
upgrade=tftp 0x1000 uImage;erase 0x20080000 0x202FFFFF;cp.b 0x1000 0x20080000 $(
filesize)
stdin=serial
stdout=serial
stderr=serial
filesize=2cf805
fileaddr=1000
netmask=255.255.240.0
ipaddr=192.168.0.2
serverip=192.168.0.9

Environment size: 579/65531 bytes
bf537>



















U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
## Booting image at 20080000 ...
Image Name: MXL Firmware Image
Created: 2009-07-24 4:02:46 UTC
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 2947013 Bytes = 2.8 MB
Load Address: 00001000
Entry Point: 00001000
Verifying Checksum ... Bad Data CRC
bf537> print
bootargs=root=/dev/mtdblock3 rw
bootcmd=run flashboot
bootdelay=2
baudrate=57600
loads_echo=1
ethaddr=02:80:ad:20:31:b8
autoload=no
rootpath=/romfs
hostname=BF537
flashboot=bootm 0x20080000
ramboot=tftp 0x01A00000 uImage;bootm;
update=tftp 0x1000 u-boot.bin;protect off 0x20000000 0x2002FFFF;erase 0x20000000
0x2002FFFF;cp.b 0x1000 0x20000000 $(filesize);
upgrade=tftp 0x1000 uImage;erase 0x20080000 0x202FFFFF;cp.b 0x1000 0x20080000 $(
filesize)
netmask=255.255.240.0
serverip=192.168.1.9
ipaddr=192.168.1.2
stdin=serial
stdout=serial
stderr=serial

Environment size: 549/65531 bytes
bf537>

[Прокопьев Максим]

не хватает места для записи нового ПО.
Чтобы выделить больше места нужно изменить переменную upgrade следующим образом:
прописываем строку

set upgrade 'tftp 0x1000 uImage;erase 0x20080000 0x203FFFFF;cp.b 0x1000 0x20080000 $(filesize)'

затем набрать команду save

и снова нужно прошить
run upgrade

[rus30]

Всё сделал теперь выдаёт вот это

U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr 192.168.0.2
bf537> set serverip 192.168.0.9
bf537> run upgrade
Unknown command '?tftp' - try 'help'
bf537>
bf537>
bf537>
bf537> save
Saving Environment to Flash...
Un-Protected 1 sectors
Un-Protected 1 sectors
Erasing Flash...
Erasing Flash locations, Please Wait
.
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
Protected 1 sectors
bf537> set ipaddr 192.168.0.2
bf537> set serverip 192.168.0.9
bf537> run upgrade
Unknown command '?tftp' - try 'help'
bf537> set upgrade tftp 0x1000 uimage;erase 0x20080000 0x203FFFFF;cp.b 0x1000 0x
20080000 $(filesize)

Erasing Flash locations, Please Wait
........................................................
Erased 56 sectors
Usage:
cp - memory copy

bf537> save
Saving Environment to Flash...
Un-Protected 1 sectors
Un-Protected 1 sectors
Erasing Flash...
Erasing Flash locations, Please Wait
.
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
Protected 1 sectors
bf537> set ipaddr 192.168.0.2
bf537> setserverip 192.168.0.9
Unknown command 'setserverip' - try 'help'
bf537> set ipaddr 192.168.0.2
bf537> set serverip 192.168.0.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.0.9; our IP address is 192.168.0.2
Filename 'uimage'.
Load address: 0x1000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 2947077 (2cf805 hex)


Повторная прошивка

U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr 192.168.0.2
bf537> set serverip 192.168.0.9
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.0.9; our IP address is 192.168.0.2
Filename 'uimage'.
Load address: 0x1000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 2947077 (2cf805 hex)


bf537> print
bootargs=root=/dev/mtdblock3 rw
bootcmd=run flashboot
bootdelay=2
baudrate=57600
loads_echo=1
ethaddr=02:80:ad:20:31:b8
autoload=no
rootpath=/romfs
hostname=BF537
flashboot=bootm 0x20080000
ramboot=tftp 0x01A00000 uImage;bootm;
update=tftp 0x1000 u-boot.bin;protect off 0x20000000 0x2002FFFF;erase 0x20000000
0x2002FFFF;cp.b 0x1000 0x20000000 $(filesize);
upgrade=tftp 0x1000 uimage
stdin=serial
stdout=serial
stderr=serial
filesize=2cf805
fileaddr=1000
netmask=255.255.240.0
ipaddr=192.168.0.2
serverip=192.168.0.9

Environment size: 516/65531 bytes
bf537>

[Прокопьев Максим]

неправильно прописали переменную upgrade

у Вас:
upgrade=tftp 0x1000 uimage

а нужно:
upgrade=tftp 0x1000 uImage;erase 0x20080000 0x203FFFFF;cp.b 0x1000 0x20080000 $(filesize)

[rus30]

я делаю так
set ipadr 192.168.0.2
set serverip 192.168.0.5
set upgrade tftp 0x1000 uImage;erase 0x20080000 0x203FFFFF;cp.b 0x1000 0x20080000 $(filesize)
далее он стирает
Erasing Flash locations, Please Wait
........................................................
Erased 56 sectors
Copy to Flash... done
затем
save
и
run upgrade

что я делаю не так
U-Boot-1.1.3-ADI-2005R4 (Apr 11 2007 - 11:12:20)

CPU: ADSP BF537 Rev.: 0.2
Board: ADI BF537 stamp board
Support: http://blackfin.uclinux.org/
Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz
SDRAM: 32 MB
FLASH: 4 MB
In: serial
Out: serial
Err: serial
Net: ADI BF537 EMAC
Hit any key to stop autoboot: 0
bf537> set ipaddr 192.168.0.2
bf537> set serverip 192.168.0.5
bf537> set upgrade tftp 0x1000 uimage;erase 0x20080000 0x203FFFFF;cp.b 0x1000 0x
20080000 $(filesize)

Erasing Flash locations, Please Wait
........................................................
Erased 56 sectors
Copy to Flash... done
bf537> seve
Unknown command 'seve' - try 'help'
bf537> save
Saving Environment to Flash...
Un-Protected 1 sectors
Un-Protected 1 sectors
Erasing Flash...
Erasing Flash locations, Please Wait
.
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
Protected 1 sectors
bf537> run upgrade
Using MAC Address 02:80:AD:20:31:B8
TFTP from server 192.168.0.5; our IP address is 192.168.0.2
Filename 'uimage'.
Load address: 0x1000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 2947077 (2cf805 hex)
bf537> print
bootargs=root=/dev/mtdblock3 rw
bootcmd=run flashboot
bootdelay=2
baudrate=57600
loads_echo=1
ethaddr=02:80:ad:20:31:b8
autoload=no
rootpath=/romfs
hostname=BF537
flashboot=bootm 0x20080000
ramboot=tftp 0x01A00000 uImage;bootm;
update=tftp 0x1000 u-boot.bin;protect off 0x20000000 0x2002FFFF;erase 0x20000000
0x2002FFFF;cp.b 0x1000 0x20000000 $(filesize);
stdin=serial
stdout=serial
stderr=serial
upgrade=tftp 0x1000 uimage
filesize=2cf805
fileaddr=1000
netmask=255.255.240.0
ipaddr=192.168.0.2
serverip=192.168.0.5

Environment size: 516/65531 bytes
bf537>