Добрый день!
Правильно ли настроен терминал под 128 ONT на канал:
При регистрации ONT профили, кроме rules, используются default.
Профили rules назначаются отталкиваясь от канала
0 = профиль 100 = vlan100
1 = профиль 101 = vlan101
С абонентской стороны используется только UNI0.
ont x 1000Код: Выделить всё
(ONT-x/1000/02:00:22:01:4F:88)# show config
Channel/ID: x/1000 MAC: 02:00:22:01:4F:88 Type: NTE-2
(OLT: x Port: x)
Secret: 1234
Description:
ONU block: no
UNI0 block: no
UNI1 block: no
RF out block: n/a
Rules profile: 101
Shaper profile: 0 Default profile
IP multicast profile: 0 Default profile
Ports profile: 0 Default profile
Paths profile: 0 Default profile
Additional network parameters:
Alternative ethertype: 0x88A8
Use for upstream: no Use for downstream: no
Код: Выделить всё
show profile rules list
2 100
3 101
show profile shaper list
0 0 Default profile
show profile ports list
0 0 Default profile
show profile path list
0 0 Default profile
show profile ipmc list
0 0 Default profile
profile rules 101Код: Выделить всё
(profile-rules)# rule show pon
0) 0: if (VID == 101) then DeleteTag; forward
1) 1: if (VID != 101) then discard
2) 14: if (LinkIndex == 0x0) then path = port 0 queue 0; forward
3) 14: if (LinkIndex == 0x3) then path = port 1 queue 1; forward
(profile-rules)# rule show uni0
0) 0: if (Always) then AddTagVID = 101; forward
1) 14: if (Always) then path = link 0 queue 0; forward
(profile-rules)# rule show uni1
profile ports 0 Код: Выделить всё
(profile-ports0)# show information
Index: 0
Description: Default profile
Links count: 2
PON port:
Auto downstream broadcast frame forwarding: yes
UNI0 port:
Enabled: yes
Autonegotiation: yes
Speed: 1Gbps
Duplex: full
Automatic learning entry limit: 64
Learned entry age limit: 60
UNI1 port:
Enabled: yes
Autonegotiation: yes
Speed: 100Mbps
Duplex: full
Automatic learning entry limit: 64
Learned entry age limit: 60
profile path 0Код: Выделить всё
(profile-path0)# show information
Index: 0
Description: Default profile
Link0 assigned to PATH ID = 0
Link1 assigned to PATH ID = 1
Link2 assigned to PATH ID = unassigned
Link3 assigned to PATH ID = unassigned
(profile-path0)# rule show path0
0) 10: if (Always) then (ClearDiscard) and (SetQueue 0) and (SetUnicastLink 0)
(profile-path0)# rule show path1
0) 10: if (Always) then (ClearDiscard) and (SetQueue 0) and (SetUnicastLink 1)
В какой-то момент один канал начал сыпаться. Обнаружил что на 0 канале уже 65 абонентов,
а на 1 канале 70, который вобщем-то и посыпался. Выполнив данную настройку по Базе Знаний -
сделал OLT0# reconfig и reboot. Пока что не ясно, работает или нет.
Что я мог упустить? В принципе мне вообше не понятны действия для "расширения" каналов (:
1) что это в ports - Automatic learning entry limit: 64
2) надо изменить rules(?)
14: if (LinkIndex == 0x0) then path = port 0 queue 0; forward
14: if (LinkIndex == 0x3) then path = port 1 queue 1; forward
на
14: if (LinkIndex == 0x0) then path = port 0 queue 0; forward
14: if (LinkIndex == 0x1) then path = port 0 queue 1; forward
3) при reconfig и reboot - ONT загрузиться уже с изменениями?