SMG-1016m overlap

[Papazian]

Доброго дня.
Есть smg-1016m (Версия ПО V.3.2.0.1098. L. M. Build: Oct 30 2014 17:44:55)
К нему подключен по Q.931 станция Panasonik 60x(точнее не знаю). Исходящие в сторону Panasonik проходя отлично.
Проблема во входящих. Номер CdPN приходят в overlap режиме, однако же в трассировке вижу только первые 3 цифры номера.
В плане набора режим overlap включал.
Беспокоит, что от Panasonik приходит progress indicator равный 3.

Вот пример вызова.

00:54:25.520452 [INFO] Q931. Line 00/04. Create Call, entry 00. Call 805A (Incoming)
00:54:25.520510 [INFO] Q931. Line 00/04. Call 805A. Incoming SETUP. Check chan id
00:54:25.520559 [INFO] Check IE 'Channel ID': channel id='as indicated' chan=31, mode non-excl
00:54:25.520611 [INFO] Line 00/04. Search B-chan: chan 31, mask 00010001 - chan ok: mask 00010001
00:54:25.520658 [INFO] Check IE 'Bearer capablity: {3.1 kHz audio}{64 kbit/s}{G.711 A-law}
00:54:25.520707 [INFO] Check IE 'Called party number': {type=0x00, plan=0x01} <898> (3)
00:54:25.520759 [INFO] Check IE 'Calling party number': {type=0x00, plan=0x01}, {presentation=0, screening=0} <372893> (6)
00:54:25.520804 [INFO] Q931. Line 00/04. Call 805A. Incoming SETUP. {PI 3} CgPN <372893>(6), CdPN <898>(3) isdn flag=02
00:54:25.520886 [INFO] Port PRI:04:00. VChan set (chan 31) - 'line 1, chan 124'
00:54:25.520954 [INFO] Port PRI:04:00. Seize (v-chan:31, TG:04). Cld:'<none>'(0). (Trunk) . Clg-len: 6. clg-set: y. COS: -1. RADIUS=-1
00:54:25.521008 [INFO] Port PRI:04:00. ModTable in [-1:-1], out [-1:-1], out redir:orig [-1:-1]
00:54:25.521064 [INFO] Port PRI:04:00. CgPN: <372893>(6) <set> <unknown> <isdn/telephony> <allowed> <not verified>. cat [2].
00:54:25.521118 [INFO] Port PRI:04:00. Calling number: 372893, use for sorm: all digits
00:54:25.521167 [INFO] Port PRI:04:00. Calling Info (pres allowed): <372893>. <Category=2>
00:54:25.521214 [INFO] Port PRI:04:00. CgPN: <372893>(6) <set> <unknown> <isdn/telephony> <allowed> <not verified>. cat [2].
00:54:25.521267 [INFO] Port PRI:04:00. Check number dir-type for <372893>[0x01] (6)
00:54:25.521318 [INFO] Port PRI:04:00. Set state 'In-Dial'
00:54:25.521366 [INFO] Q931. Line 00/04. Call 805A. Incoming seize - PLAN 0. COS 0
00:54:25.521411 [INFO] Q931. Line 00/04. Call 805A. Incoming SETUP. {PI 3} proc dial
00:54:25.521454 [INFO] Q931. Line 00/04. Call 805A. State 'Overlap Receiving'
00:54:25.521504 [INFO] Q931. Line 00/04. Call 805A. In Dial: 898
00:54:25.521552 [INFO] Q931. Line 00/04. Call 805A. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
00:54:25.521613 [INFO] Port PRI:04:00. Dial In (in=03, need rm=0): <8><9><8> (flg=next)
00:54:25.521662 [INFO] Port PRI:04:00. In Digit 3 sym: called buf <898>
00:54:25.521705 [INFO] Port PRI:04:00. Dial buf <898>(3)
00:54:25.521754 [INFO] Q931. Line 00/04. Call 805A. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
00:54:25.521851 [INFO] Q931. Line 00/04. Call 805A. TX 11
DUMP: 08.02.80.5A.0D.18.03.A9.83.9F.
0x005A (to orig), MSG=SETUP ACKNOWLEDGE:
[channel id: channel=31 (exclusive)] Coding=CCITT
---------------------------------
00:54:25.521947 [INFO] Port PRI:04:00. Dial Proc (state In-Dial, called len 03): <898>
00:54:25.522036 [INFO] Port PRI:04:00. Dial Proc. RADIUS return-code: [0].
00:54:25.522091 [INFO] Port PRI:04:00. Search route. Mode: 'calling'. Num: <372893>(6).# Complete
00:54:25.522162 [INFO] Port PRI:04:00. Search route. result: route not found. res (-1)
00:54:25.522214 [INFO] Port PRI:04:00. Check number dir-type for <898>[0x01] (3)
00:54:25.522266 [INFO] Port PRI:04:00. Search route. Mode: 'called'. Num: <898>(3).
00:54:25.522332 [INFO] Port PRI:04:00. Search route. result: route not found. res (-1)
00:54:25.522385 [INFO] Port PRI:04:00. Release, cause 'No route to destination', dcl '0', loc '0'
00:54:25.522432 [INFO] Port PRI:04:00. SormRelease in state 'In-Dial'. Flg: 0
00:54:25.522487 [INFO] Port PRI:04:00. Save CDR. disabled. [0x0]
00:54:25.522535 [INFO] Port PRI:04:00. Set state 'Release'
00:54:25.522585 [INFO] Port PRI:04:00. Disconnect, cause 'No route to destination', dcl '0', loc '0'
00:54:25.522632 [INFO] Port PRI:04:00. SormRelease in state 'Release'. Flg: 0
00:54:25.522683 [INFO] Port PRI:04:00. Save CDR. disabled. [0x0]
00:54:25.522731 [INFO] Port PRI:04:00. Set signal: 'BUSY'

Помогите победить эту проблему.

[Evgeniy]

Пришлите полные логи вызова (PBX трассировки по всем параметрам 1) на адрес 3036@eltex.org