Smg-2 Таймеры

[Maksimus]

Добрый день!
Как избавиться от длительного времени набора через шлюз.
Как я понимаю происходит это из-за S-таймера, который я выкрутил в 0, но изменения не применяются.
Подскажите в чем может быть проблема?
Ниже приложил конфиг и лог вызова.

name: 'From-Operator-to-Asterisk'
type: 'trunk'
idx: 1
access cat: 0 [no check]
direction: 'local'
CdPN type: '<no-change>'
CdPN npi: 'transit'
get CID: n
need CID: n
dial mode: enblock
not dial ST: no
priority: 100
Stimer: 0
Ltimer: 10
duration: 20
PLAN: 0
Mask for prefix [00]:
[014] - [called]
mask: (7105|7[25]55|778[1-57])
Ltimer: 0
Stimer: 0
Duration: 30

10:49:57.105934 [INFO] Q931. Line 00/00. Call 8012. State 'Overlap Receiving'
10:49:57.106045 [INFO] Q931. Line 00/00. Call 8012. In Dial: 7782
10:49:57.106095 [INFO] Q931. Line 00/00. Call 8012. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
10:49:57.106152 [INFO] Port PRI:00:00. Dial In (in=04, need rm=0): <7><7><8><2> (flg=next)
10:49:57.106311 [INFO] Port PRI:00:00. In Digit 4 sym: called buf <7782>
10:49:57.106364 [INFO] Port PRI:00:00. Dial buf <7782>(4)
10:49:57.106408 [INFO] Q931. Line 00/00. Call 8012. Timer 'T302' (15 sec) start in state 'Overlap Receiving'
10:49:57.106483 [INFO] Q931. Line 00/00. Call 8012. TX 10
DUMP: 08.01.92.0D.18.03.A9.83.8B.
0x12 (to orig), MSG=SETUP ACKNOWLEDGE:
[channel id: channel=11 (exclusive)] Coding=CCITT
---------------------------------
10:49:57.106595 [INFO] Port PRI:00:00. Dial Proc (state In-Dial, called len 04): <7782>
10:49:57.106645 [INFO] Port PRI:00:00. Dial Proc. RADIUS return-code: [0].
10:49:57.106690 [INFO] Port PRI:00:00. Search route. Mode: 'calling'. Num: <7215>(4).# Complete
10:49:57.106764 [INFO] Port PRI:00:00. Search route. result: route not found. res (-1)
10:49:57.106812 [INFO] Port PRI:00:00. Search route. Mode: 'called'. Num: <7782>(4).
10:49:57.106993 [INFO] Port PRI:00:00. Search route. result: incomplete route: L[20] S[5] D[30]. res (0)
10:50:02.178154 [INFO] Port PRI:00:00. S-TimeOut. Try Route to [-1]
10:50:02.178251 [INFO] Port PRI:00:00. Dial In (in=01, need rm=0): [.]
10:50:02.178295 [INFO] Port PRI:00:00. In Digit 1 sym: called buf <7782.>
10:50:02.178335 [INFO] Port PRI:00:00. Dial buf <7782>(4)
10:50:02.178377 [INFO] Port PRI:00:00. Dial Proc (state In-Dial, called len 05): <7782.> Compl.
10:50:02.178418 [INFO] Port PRI:00:00. Dial Proc. RADIUS return-code: [0].
10:50:02.178468 [INFO] Port PRI:00:00. Search route. Mode: 'called'. Num: <7782.>(5).# Complete
10:50:02.178668 [INFO] Port PRI:00:00. Search route. result: found route: prefix[0]. res (4)
10:50:02.178719 [INFO] Port PRI:00:00. Process route to prefix[0]. (0 attempt)
10:50:02.178764 [INFO] Port PRI:00:00. Send 'End of Dial' to incoming call
10:50:02.178805 [INFO] Q931. Line 00/00. Call 8012. End Dial in state 'Overlap Receiving' (condition for call proceeding reached)
10:50:02.178848 [INFO] Q931. Line 00/00. Call 8012. Timer 'T302' stop in state 'Overlap Receiving'
10:50:02.178911 [INFO] Q931. Line 00/00. Call 8012. TX 5
DUMP: 08.01.92.02.
0x12 (to orig), MSG=CALL PROCEEDING:
---------------------------------
10:50:02.178961 [INFO] Q931. Line 00/00. Call 8012. State 'Incoming Call Proceeding'
10:50:02.179006 [INFO] Port PRI:00:00. Prefix 00: type 'TRUNK', idx=1
10:50:02.179047 [INFO] Port PRI:00:00. Accs on
10:50:02.179089 [INFO] Port PRI:00:00. Link to TG 01. Out modifiers-table: clg[-1], cld[-1], redir[-1], orig[-1], generic[-1]
10:50:02.179133 [INFO] Port PRI:00:00. Link to TG 01. Setup mode: enblock <ST>
10:50:02.179174 [INFO] Port PRI:00:00. Link to TG 01: mode Local. Dir=0, Cld=0 Select Order=. In buf: ~7782.
10:50:02.179217 [INFO] Port PRI:00:00. TG: Link entry to SIPT[00]
10:50:02.179261 [INFO] Port PRI:00:00. Outgoing setup to SIPT:0000.
10:50:02.179303 [INFO] SIPT[00]. Seize from port PRI:00:00.
10:50:02.179382 [INFO] Port SIPT:0422. Check out-calling-modify: '7215'(4). ModTable[-1], ClgMod[-1]
10:50:02.179433 [INFO] Port SIPT:0422. Check out-calling-from-RADIUS-modify: '7215'(4). ClgMod[-1]
10:50:02.179479 [INFO] SIPT[00]. Seize - interface 0 [ID: 01]: set host:port 10.210.81.9:5060
10:50:02.179526 [INFO] Port SIPT:0422. Set parent PRI:00:00
10:50:02.179566 [INFO] Port SIPT:0422. VChanIP set - 'line 0, chan 44'
10:50:02.179629 [INFO] Port SIPT:0422. Create msp-conn Conn[000b].
10:50:02.179995 [INFO] Port SIPT:0422. Set new IP Conn[000b] with chan[44]
10:50:02.180070 [INFO] SIP. Callref 0422. IP-conn [000b] ready
10:50:02.180120 [INFO] Port SIPT:0422. loc 0, trunk-loc 0. peer-loc 0, peer-tunk-loc: 0
10:50:02.180228 [INFO] Port PRI:00:00. loc 0, trunk-loc 0. peer-loc 0, peer-tunk-loc: 0
10:50:02.180280 [INFO] SIPT[00]. Seize - dst '10.210.81.9:5060' src-port 0
10:50:02.180323 [INFO] SIPT[00]. Seize CgPN: <7215>(4) <set> <unknown> <unknown> <allowed> <net.provided>. cat [1](0x31)
10:50:02.180369 [INFO] SIPT[00]. Seize - calling category: '1' convert to ISUP category 10
10:50:02.180413 [INFO] SIPT[00]. Seize (HLC 2 bytes) - enblock mode
10:50:02.180454 [INFO] Port SIPT:0422. Set state 'Wait-Num'
10:50:02.180504 [INFO] Port SIPT:0422. Query Next Digit - peer PRI:00:00 (next.digit=n). Called len 05, proceed 00
10:50:02.180545 [INFO] Port SIPT:0422. Dial Out=7 (ext)
10:50:02.180587 [INFO] Port SIPT:0422. Check out-called-modify: '7'(1). ModTable[-1], CldMod[-1]
10:50:02.180631 [INFO] SIP. Callref 0422. Dial 7
10:50:02.180711 [INFO] Port SIPT:0422. Dial Out: called len 00, append 01 (max digit 30)
10:50:02.180771 [INFO] Port SIPT:0422. Query Next Digit - peer PRI:00:00 (next.digit=n). Called len 05, proceed 01
10:50:02.180846 [INFO] Port SIPT:0422. Dial Out=7 (ext)
10:50:02.180892 [INFO] SIP. Callref 0422. Dial 7
10:50:02.180930 [INFO] Port SIPT:0422. Dial Out: called len 01, append 01 (max digit 30)
10:50:02.180981 [INFO] Port SIPT:0422. Query Next Digit - peer PRI:00:00 (next.digit=n). Called len 05, proceed 02
10:50:02.181021 [INFO] Port SIPT:0422. Dial Out=8 (ext)
10:50:02.181061 [INFO] SIP. Callref 0422. Dial 8
10:50:02.181098 [INFO] Port SIPT:0422. Dial Out: called len 02, append 01 (max digit 30)
10:50:02.181147 [INFO] Port SIPT:0422. Query Next Digit - peer PRI:00:00 (next.digit=n). Called len 05, proceed 03
10:50:02.181187 [INFO] Port SIPT:0422. Dial Out=2. (ext)
10:50:02.181227 [INFO] SIP. Callref 0422. Dial 2.
10:50:02.181263 [INFO] Port SIPT:0422. Dial Out: called len 03, append 02 (max digit 30)
10:50:02.181302 [INFO] Port SIPT:0422. Dial Out: 'End_of_Dial' digit/stop dial
10:50:02.181529 [INFO] SIP. Callref 0422. New state 'SIPT_OVL_SENDING'
10:50:02.181578 [INFO] Port SIPT:0422. Setup Ack (peer=PRI:00:00)
10:50:02.181620 [INFO] Port SIPT:0422. Set state 'Out-Dial'
10:50:02.181663 [INFO] Port PRI:00:00. Setup Acked in state In-Dial. (peer=SIPT:0422)
10:50:02.181707 [INFO] Port PRI:00:00. LinkUp to SIPT:0422
10:50:02.181749 [INFO] Port SIPT:0422. Activate IP-conn [000b]

[Bokrenok]

Встречная АТС может присылать индикатор "sending complete" в SETUP?
по наличию этого индикатора SMG-2 будет сразу обрабатывать вызов не ожидая дополнительного набора.

п.с. а таймер где крутили? надо его изменить в конкретной маске префикса, которая соответствует номеру "7782"

[Maksimus]

По встречной АТС уточняю, сам не имею к ней доступа.
п.с. таймер крутил в маске, реакции нет.

[bravo]

По встречной АТС уточняю, сам не имею к ней доступа.
п.с. таймер крутил в маске, реакции нет.

я бы встречную станцию заставил/упросил сделать набор enblock... оверлап этот нехороший уже нафиг никому не нужен.