Элтекс

производство оборудования для телекоммуникаций
http://forum.eltex-co.ru/

SMG-1016M FW 3.7.0

http://forum.eltex-co.ru/viewtopic.php?f=7&t=6631

Страница 1 из 1

SMG-1016M FW 3.7.0

Добавлено: 07 окт 2016 15:05
mustdie
Помогите разобраться в причине отбоя звонков при переходе на версию 3.7.0 с 3.6.0
Есть два PRI потока для связи с офисными станциями. При звонках с этих станций шлюз отбивает вызов. При входящих с SIP на станции все нормально.

Лог такой:

12:19:23.241920 [INFO] Q931. Line 00/01. Call FF19. RX 32
DUMP: 08.02.7F.19.05.A1.04.03.80.90.A3.18.03.A9.83.9A.
6C.05.41.80.32.31.33.70.07.80.34.32.31.32.31.31.
0x7F19 (from orig), MSG=SETUP:
[sending complete]
[bearer capability:
cap=speech
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=26 (exclusive)] Coding=CCITT
[calling party number: 213 (type=subscriber, plan=ISDN, present.allowed, not screened)]
[called party number: 421211 (type=unknown, plan=unknown)]
---------------------------------
12:19:23.242787 [INFO] Q931. Line 00/01. Create Call, entry 12. Call FF19 (Incoming)
12:19:23.242925 [INFO] Q931. Line 00/01. Call FF19. Incoming SETUP. Check chan id
12:19:23.243028 [INFO] Q931. Line 00/01. Call FF19. Check IE 'Channel ID': channel id='as indicated'chan=26, mode excl
12:19:23.243130 [INFO] Q931. Line 00/01. Search B-chan: chan 26, mask 00010001 - chan ok: mask 00010001
12:19:23.243228 [INFO] Q931. Line 00/01. Call FF19. Check IE 'Bearer capablity': {speech}{64 kbit/s}{G.711 A-law}
12:19:23.243326 [INFO] Q931. Line 00/01. Call FF19. Check IE 'Called party number': {type=0x00, plan=0x00} <421211> (6)
12:19:23.243427 [INFO] Q931. Line 00/01. Call FF19. Check IE 'Calling party number': {type=0x04, plan=0x01}, {presentation=0, screening=0} <213> (3)
12:19:23.243513 [INFO] Q931. Line 00/01. Call FF19. Incoming SETUP. CgPN <213>(3), CdPN <421211>(6) isdn flag=03
12:19:23.243643 [INFO] Port PRI:01:12. VChan set (chan 26) - 'line 0, chan 105'
12:19:23.243742 [INFO] Port PRI:01:12. Set cdr-time for: setup
12:19:23.243879 [INFO] Port PRI:01:12. Setup time-stamp: 12:19:23.296 GMT+5 Fri Oct 07 2016
12:19:23.243975 [INFO] Port PRI:01:12. Set direct prefix [2]
12:19:23.244064 [INFO] Port PRI:01:12. Seize (v-chan:26, TG:05). Cld:'<none>'(0). (Trunk) . Clg-len: 3. clg-set: y. COS: -1. RADIUS=-1
12:19:23.244162 [INFO] Port PRI:01:12. ModTable in [-1:-1], out [-1:-1], out redir:orig [-1:-1]
12:19:23.244258 [INFO] Port PRI:01:12. CgPN: <213>(3) <set> <subscriber> <isdn/telephony> <allowed> <not verified>. cat [1].
12:19:23.244361 [INFO] Port PRI:01:12. Calling Info (pres allowed): <213>. <Category=1>
12:19:23.244451 [INFO] Port PRI:01:12. CgPN: <213>(3) <set> <subscriber> <isdn/telephony> <allowed> <not verified>. cat [1].
12:19:23.244569 [INFO] Port PRI:01:12. Set state 'In-Dial'
12:19:23.244658 [INFO] Port PRI:01:12. Direct route to pfx[2]
12:19:23.244747 [INFO] Q931. Line 00/01. Call FF19. Incoming seize - PLAN 0. COS 0
12:19:23.244834 [INFO] Q931. Line 00/01. Call FF19. Incoming SETUP. proc dial
12:19:23.244922 [INFO] Q931. Line 00/01. Call FF19. State 'Call Present'
12:19:23.245014 [INFO] Q931. Line 00/01. Call FF19. In Dial: 421211{EndOfDial}
12:19:23.245103 [INFO] Q931. Line 00/01. Call FF19. Timer 'T302' (15 sec) start in state 'Call Present'
12:19:23.245210 [INFO] Port PRI:01:12. Dial In (in=07, need rm=0): <4><2><1><2><1><1>[.]
12:19:23.245299 [INFO] Port PRI:01:12. In Digit 7 sym: called buf <421211.>
12:19:23.245386 [INFO] Port PRI:01:12. Dial buf <421211>(6)
12:19:23.245476 [INFO] Port PRI:01:12. Dial Proc (state In-Dial, called len 07): <421211.> Compl.
12:19:23.245577 [INFO] Port PRI:01:12. Release, cause 'Invalid number format(incomplete number)', dcl '0', loc '0'
12:19:23.245673 [INFO] Port PRI:01:12. Set cdr-time for: release
12:19:23.245803 [INFO] Port PRI:01:12. Setup time-stamp: 12:19:23.296 GMT+5 Fri Oct 07 2016
12:19:23.245929 [INFO] Port PRI:01:12. Release time-monot: 219.298
12:19:23.246013 [INFO] Port PRI:01:12. Release time-stamp: 12:19:23.000 GMT+5 Fri Oct 07 2016, msec-diff: 219298
12:19:23.246121 [INFO] Port PRI:01:12. Duration sec: 0, msec: 0
12:19:23.246213 [INFO] Port PRI:01:12. Save CDR. disabled. [0x0]
12:19:23.246303 [INFO] Port PRI:01:12. Set state 'Release'
12:19:23.246392 [INFO] Port PRI:01:12. Disconnect, cause 'Invalid number format(incomplete number)', dcl '0', loc '0'
12:19:23.246486 [INFO] Port PRI:01:12. Save CDR. disabled. [0x0]
12:19:23.246575 [INFO] Port PRI:01:12. Set signal: 'BUSY'
12:19:23.246700 [INFO] Q931. Line 00/01. Call FF19. Disconnect call in state 'Call Present'
12:19:23.246823 [INFO] Q931. Line 00/01. Call FF19. TX 10
DUMP: 08.02.FF.19.5A.08.02.80.9C.
0x7F19 (to orig), MSG=RELEASE COMPLETE:
[cause: Invalid number format(incomplete number) (location=user, std=CCITT)]
---------------------------------
12:19:23.247092 [INFO] Port PRI:01:12. Release Complete, cause 'Normal, unspecified', dcl '0', loc '0'
12:19:23.247198 [INFO] Port PRI:01:12. Save CDR. disabled. [0x0]
12:19:23.252170 [INFO] Port PRI:01:12. Set state 'Ready'
12:19:23.252283 [INFO] Q931. Line 00/01. Call FF19. State 'Null'
12:19:23.252380 [INFO] Port PRI:01:12. Set state 'Release'

Re: SMG-1016M FW 3.7.0

Добавлено: 07 окт 2016 15:11
mustdie
А это префикс куда вызов направляется:

2:
ID: 6
name: sip-asterisk-office
type: trunk
idx: 2
accs-cat: 0
accs-check: no
numplan: 0
direction: local
cdpn_type: transit
cdpn_npi: transit
getAON: no
needAON: no
dial_mode: nochange
not_dial_ST: no
priority: 100
Ltimer: 10
Stimer: 5
Duration: 30
session_time: 0
2:
ID: 4
mask: (112|0x|[3-5]xxxxx|[78]x{10,10}|[78]10x{11,15}|9x8x{10,10})
prefix: 2
type: called
Stimer: 1
Ltimer: 10
Duration: 30

Re: SMG-1016M FW 3.7.0

Добавлено: 07 окт 2016 16:21
bravo
а тут точно все логи ? и SIP сторона была включена?
а то мож это астериск отправляет такой коз?

Re: SMG-1016M FW 3.7.0

Добавлено: 07 окт 2016 16:30
Анна
Попробуйте сделать следующим образом: создайте модификатор и поменяйте тип плана нумерации CdPN на ISDN. Модификатор назначьте на входящую транк группу

Re: SMG-1016M FW 3.7.0

Добавлено: 18 окт 2016 13:14
SEA
Доброго всем дня.

Присоединяюсь - у меня почти такая же история при переходе с ПО 3.6.0 на 3.7.0: есть схема записи переговоров с организацией транзита через SMG-2016, т.е цепочка следующая БКП - SMG-2016- Cisco 2911. На самом SMG-2016 поток с БКП в один порт Е1 входит, а через другой порт Е1 выходит, т.е. никакого IP сегмента прохождения сигнала нет.

Снял трэйс на потоке, смотрящем в БКП:
SMG-2016. SN: VI2A000510 Software Version: ECSS-10 V.3.7.0.1932 2016/PBX/VAS/REC/IVR Build: Sep 9 2016 04:50:05
Log started at: 09:04:40.843992 26/09/16
Trace levels:
alarm - 00
calls - 00
isup - 00
q931 - 99
sipt - 00
rtp - 00
msp - 00
radius - 00
ivr - 00
09:04:40.941660 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:40.941737 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:40.941797 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:41.943252 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:41.943334 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:41.943391 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:42.944882 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:42.944984 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:42.945043 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:43.946483 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:43.946563 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:43.946620 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:44.948094 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:44.948190 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:44.948255 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:45.949687 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:45.949770 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:45.949826 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:46.951265 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:46.951340 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:46.951396 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:47.952866 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:47.952960 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:47.953017 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:48.954467 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:48.954552 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:48.954608 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:49.956106 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:49.956199 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:49.956261 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:50.957696 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:50.957782 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:50.957838 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:51.555172 [INFO] Q931. Line 00/01. Call 8007. RX 37
DUMP: 08.02.00.07.05.A1.04.03.80.90.A3.18.03.A9.83.9F.
6C.09.00.81.30.37.38.34.33.39.32.70.08.80.30.37.
38.34.33.33.33.
0x0007 (from orig), MSG=SETUP:
[sending complete]
[bearer capability:
cap=speech
std=CCITT
rate=64 kbit/s
mode=circuit
layer1=G.711 A-law]
[channel id: channel=31 (exclusive)] Coding=CCITT
[calling party number: 0784392 (type=unknown, plan=unknown, present.allowed, verifed & pass)]
[called party number: 0784333 (type=unknown, plan=unknown)]
---------------------------------
09:04:51.555237 [INFO] Q931. Line 00/01. Create Call, entry 10. Call 8007 (Incoming)
09:04:51.555293 [INFO] Q931. Line 00/01. Call 8007. Incoming SETUP. Check chan id
09:04:51.555342 [INFO] Q931. Line 00/01. Call 8007. Check IE 'Channel ID': channel id='as indicated'chan=31, mode excl
09:04:51.555386 [INFO] Q931. Line 00/01. Search B-chan: chan 31, mask 00010001 - chan ok: mask 00010001
09:04:51.555428 [INFO] Q931. Line 00/01. Call 8007. Check IE 'Bearer capablity': {speech}{64 kbit/s}{G.711 A-law}
09:04:51.555472 [INFO] Q931. Line 00/01. Call 8007. Check IE 'Called party number': {type=0x00, plan=0x00} <0784333> (7)
09:04:51.555517 [INFO] Q931. Line 00/01. Call 8007. Check IE 'Calling party number': {type=0x00, plan=0x00}, {presentation=0, screening=1} <0784392> (7)
09:04:51.555553 [INFO] Q931. Line 00/01. Call 8007. Incoming SETUP. CgPN <0784392>(7), CdPN <0784333>(7) isdn flag=03
09:04:51.555631 [INFO] Q931. Line 00/01. Call 8007. Incoming seize - PLAN 0. COS 0
09:04:51.555705 [INFO] Q931. Line 00/01. Call 8007. Incoming SETUP. proc dial
09:04:51.555748 [INFO] Q931. Line 00/01. Call 8007. State 'Call Present'
09:04:51.555790 [INFO] Q931. Line 00/01. Call 8007. In Dial: 0784333{EndOfDial}
09:04:51.555828 [INFO] Q931. Line 00/01. Call 8007. Timer 'T302' (15 sec) start in state 'Call Present'
09:04:51.555935 [INFO] Q931. Line 00/01. Call 8007. Disconnect call in state 'Call Present'
09:04:51.556024 [INFO] Q931. Line 00/01. Call 8007. TX 10
DUMP: 08.02.80.07.5A.08.02.80.9C.
0x0007 (to orig), MSG=RELEASE COMPLETE:
[cause: Invalid number format(incomplete number) (location=user, std=CCITT)]
---------------------------------
09:04:51.556100 [INFO] Q931. Line 00/01. Call 8007. State 'Null'
09:04:51.959301 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:51.959376 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:51.959432 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
09:04:52.960927 [INFO] Q931. Line 00/00. lnk: [1]. strt: [1]
09:04:52.961022 [INFO] Q931. Line 00/01. lnk: [1]. strt: [1]
09:04:52.961080 [INFO] Q931. Line 00/03. lnk: [1]. strt: [1]
SMG-2016. SN: VI2A000510 Software Version: ECSS-10 V.3.7.0.1932 2016/PBX/VAS/REC/IVR Build: Sep 9 2016 04:50:05
Log stopped at: 09:04:53.684990 26/09/16

Та же самая каза - Invalid number format(incomplete number) (location=user, std=CCITT).
Т.е. cause отправил БКП и чего то ему не понравилось, думаю, что-то связанное с планом нумерации или типом номера (хотя он не менялся).
Машина в боевой работе, замена софта производилась рано утром после кучи согласований и тут на тебе...быстро откатился назад на 3.6.0 и всё пошло...разбираться времени и возможности нет :(
К Элтексу - если что-то поменялось в дефолтных настройках или таймерах или ещё в чём, отпишитесь. В листе изменений к пакету ничего такого нет...

Re: SMG-1016M FW 3.7.0

Добавлено: 18 окт 2016 14:13
Dmitriy_eltex
Здравствуйте, коллеги.

Данная проблема известная и связана она с обработкой типа номера unknown.
Просьба, всем у кого возникла данная проблема установить это ПО:
smg1016m
http://eltex.nsk.ru/upload/iblock/c80/s ... 0.1944.bin
smg2016
http://eltex.nsk.ru/upload/iblock/b37/s ... 0.1944.bin

Re: SMG-1016M FW 3.7.0

Добавлено: 20 окт 2016 15:01
SEA
Спасибо, помогло.
Часовой пояс: UTC+07:00
Страница 1 из 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/