Попался в руки шлюз TAU8 не получает адрес по DHCP, не сбрасывается кнопкой F
по COM порту доступен, грузится, и эта вся его активность
очень смущает при загрузке
*** Warning - bad CRC or NAND, using default environment
при этом ethernet порт рабочий если например лить прошивку по инструкции http://kcs.eltex.nsk.ru/articles/141 (когда попал мне в руки подозревал что прошивку закосячили) то спокойно можно назначить адрес получить по tftp всё.
При этом на нем сохранились какие то сотатки старой конфигурации сетевой (гейтвей и днсы)
Может знающие люди подскажут можно что то с ним сделать или уже в помойку только?
Спасибо.
# c1k pre-boot loader
Init DDR.. Wait cplt..
Training(0)..
DDR Training.............................................................Done
DDR training complete at 0 cycle
Ok
Init nand
Scan chip
NAND 32 MiB (NAND 32MiB 3,3V 8-bit) (block 512 octets)
arm clk: 650000000
ddr clk: 375000000
1..
U-boot image loaded, do go
U-boot image start
NAND timings init
U-Boot 1.1.6 (Jul 7 2011 - 11:59:39) Mindspeed $Name: u-boot_6_00_4 $
DRAM: 256 MB
Comcerto Flash Subsystem Initialization
Flash: 0 kB
NAND: board_nand_init nand->IO_ADDR_R =30000000
32 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Reserve MSP memory
Net: comcerto_gemac0, comcerto_gemac1
Detected RTL8201FL
Enter 'stop' for stop autoboot
NAND read: device 0 offset 0x260000, size 0x400000
Reading data from 0x65fe00 -- 100% complete.
4194304 bytes read: OK
Reading data from 0x3e00 -- 100% complete.
get_factory_str: init=/etc/preinit root=/dev/mtdblock4 rootfstype=jffs2 ro user_ debug=31 hw_model=TAU-8.IP hw_revision=1v6 hwaddress=eth0,A8:F9:4B:09:30:5A,eth2 ,02:20:80:A8:F9:4B console=ttyS0,115200 mtdparts=comcertonand:256k(u-boot),128k( env),2048k(config),4096k(kernel),24000k(fs)
## Booting image at 81000000 ...
Image Name: Linux-2.6.33.5
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2321064 Bytes = 2.2 MB
Load Address: 80808000
Entry Point: 80808000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.33.5 (igor@igor-desktop) (gcc version 4.1.2) #23 Tue May 19 08 :51:28 NOVT 2015
CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387d
CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
Machine: Comcerto 1000 (EVM)
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62992
Kernel command line: init=/etc/preinit root=/dev/mtdblock4 rootfstype=jffs2 ro u ser_debug=31 hw_model=TAU-8.IP hw_revision=1v6 hwaddress=eth0,A8:F9:4B:09:30:5A, eth2,02:20:80:A8:F9:4B console=ttyS0,115200 mtdparts=comcertonand:256k(u-boot),1 28k(env),2048k(config),4096k(kernel),24000k(fs) partno=M83241G fppmode=1
Hardware model: TAU-8.IP
Board type: 3
Hardware revision: 1.0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 248MB = 248MB total
Memory: 246784KB available (4268K code, 278K data, 132K init, 0K highmem)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:80
Calibrating delay loop... 648.80 BogoMIPS (lpj=3244032)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
SPI core: loaded version 0.2
PCIe0: no device detected on link (3)
PCIe1: no device detected on link (3)
pcie_setup(0)
pcie_scan_bus(0)
PCI: bus0: Fast back to back transfers enabled
pcie_setup(1)
pcie_scan_bus(1)
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
SPI core: add adapter comcerto-spi
arm1: Module loaded.
Registering mini_fo version $Id: 209-mini_fo.patch,v 1.1.2.1 2010/06/21 09:34:58 satananda.burla Exp $
Slow work thread pool: Starting up
Slow work thread pool: Ready
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
msgmni has been set to 482
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
console [ttyS0] enabled
loop: module loaded
nbd: registered device at major 43
st: Version 20081215, fixed bufsize 32768, s/g segs 256
NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (Hynix NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks
7 cmdlinepart partitions found on MTD device comcertonand
Creating 7 MTD partitions on "comcertonand":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000060000 : "env"
0x000000060000-0x000000260000 : "config"
0x000000260000-0x000000660000 : "kernel"
0x000000660000-0x000001dd0000 : "fs"
0x000001dd0000-0x000001fc4000 : "driver"
0x000001fc4000-0x000001fd4000 : "default_config"
c1k_eth_probe: gemac 0
PHY ID1=001C ID2=C816
Configure GEMAC0 as MII for RTL8201FL
Start link timer
eth0: C1000 Ethernet Controller a8:f9:4b:09:30:5a
c1k_eth_probe: gemac 1
PHY ID1=001C ID2=C816
eth2: C1000 Ethernet Controller 02:20:80:a8:f9:4b
MDC divider: 96
Comcerto MDIO Bus: probed
MDC divider: 96
Comcerto MDIO Bus: probed
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoE module inited
PPPoL2TP kernel driver, V1.0
usbcore: registered new interface driver catc
catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
usbcore: registered new interface driver kaweth
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
usbcore: registered new interface driver rtl8150
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_eem
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver smsc95xx
usbcore: registered new interface driver gl620a
usbcore: registered new interface driver net1080
usbcore: registered new interface driver plusb
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver MOSCHIP usb-ethernet driver
usbcore: registered new interface driver int51x1
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
tdi_reset: set Streaming disable mode
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: comcerto EHCI
comcerto-ehci comcerto-ehci.1: new USB bus registered, assigned bus number 1
comcerto-ehci comcerto-ehci.1: irq 5, io mem 0x0f000000
tdi_reset: set Streaming disable mode
comcerto-ehci comcerto-ehci.1: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: comcerto EHCI
usb usb1: Manufacturer: Linux 2.6.33.5 ehci_hcd
usb usb1: SerialNumber: comcerto-ehci.1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapter s
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for IPWireless converter
usbcore: registered new interface driver ipwtty
ipw: v0.3:IPWireless tty driver
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
i2c /dev entries driver
cpuidle: using governor ladder
(NTE-)RG: init eltex watchdog
nf_conntrack version 0.5.0 (3860 buckets, 15440 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing NETLINK_KEY socket
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
lib80211: common routines for IEEE802.11 drivers
VFS: Mounted root (jffs2 filesystem) readonly on device 31:4.
Freeing init memory: 132K
Please be patient, while OpenWrt loads ...
- preinit -
./sbin/mount_root
board: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
Init proprietary Eltex NTE-RG/RG board driver
Board info available
Board type: TAU
Board switch to normal mode
restore saved config
CRC0: Ok CRC1: Ok
Flag0: 1 Flag1: 0
uncompressed 20805 bytes from device 0
restore ret: 0
Conf restore
Cleaning unused 3G provider files...
For TAU-4/8.IP-W
----------------------- encrypt_config -----------------------
init_settings
wifi_config_load: time(6)
Wi-Fi: 'disable'.
read_network_config: Common settings load
common_settings_load...
save_variable: PING_SERVERS=
read_network_config: USB-modem config load
usb_modem_config_load...
Can't open config 'usb_modems'.
read_network_config: Access settings load
access_settings_load...
read_network_config: load config (network)
Wi-Fi (disable).
1st DNS (192.168.0..1).
2nd DNS (192.168.0.2).
Default GW (10.10.10.10).
Local DNS Server (disable).
IGMP Proxy (disable).
bridge(0) / dhcps (0)
wan-iface: (eth0)
protocol: (Static)
MTU '1500'
Connection mode : (wired).
Preferred channel: (wired).
save config
CRC0: Ok CRC1: Ok
Flag0: 1 Flag1: 0
next: 1
compressed 20876 bytes to device 1
-----------------------------------------------------
Registering the module 'slic' for Si3217x device
-----------------------------------------------------
Set major number 64.
SPI core: add driver si3217x
SPI core: attach client to adapter comcerto-spi
slic0 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic1 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic2 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic3 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic4 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic5 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic6 device probe. Chip ID: 0xa2 si32176 rev.C
SPI core: attach client to adapter comcerto-spi
slic7 device probe. Chip ID: 0xa2 si32176 rev.C
-----------------------------------------------------
Device initialization.
-----------------------------------------------------
slic0 patch load ok
slic1 patch load ok
slic2 patch load ok
slic3 patch load ok
slic4 patch load ok
slic5 patch load ok
slic6 patch load ok
slic7 patch load ok
slic0 start init
slic1 start init
slic2 start init
slic3 start init
slic4 start init
slic5 start init
slic6 start init
slic7 start init
IOCTL_SET_STATUS2
IOCTL_SET_STATUS1
Green: 0 Red: 0
TAU-8.IP without Wi-Fi
Start loading Wi-Fi modules...
Compat-wireless backport release: compat-wireless-2.6.38-3-ns
Backport based on linux-2.6-allstable.git v2.6.38
cfg80211: Calling CRDA to update world regulatory domain
slic0 start calibration
slic1 start calibration
slic2 start calibration
slic3 start calibration
slic4 start calibration
slic5 start calibration
slic6 start calibration
slic7 start calibration
Wi-Fi modules loaded.
slic0 calibration complete
slic1 calibration complete
slic2 calibration complete
slic3 calibration complete
slic4 calibration complete
slic5 calibration complete
slic6 calibration complete
slic7 calibration complete
slic0 init done
slic1 init done
slic2 init done
slic3 init done
slic4 init done
slic5 init done
slic6 init done
slic7 init done
Can't up wlan0!
Cleaning unused 3G provider files...
For TAU-4/8.IP-W
----------------------- dhcps -----------------------
init_settings
wifi_config_load: time(13)
Wi-Fi: 'disable'.
read_network_config: Common settings load
common_settings_load...
read_network_config: USB-modem config load
usb_modem_config_load...
Can't open config 'usb_modems'.
read_network_config: Access settings load
access_settings_load...
read_network_config: load config (network)
Wi-Fi (disable).
1st DNS (192.168.0.1).
2nd DNS (192.168.0.2).
Default GW (10.10.10.10).
Local DNS Server (disable).
IGMP Proxy (disable).
bridge(0) / dhcps (0)
wan-iface: (eth0)
protocol: (Static)
MTU '1500'
Connection mode : (wired).
Preferred channel: (wired).
Service0: (Internet)
No dhcps. Ignoring service.
Service1: ()
Not active service.
Service2: ()
Not active service.
dns1='192.168.0.1'
dns2='192.168.0.2'
run_localdns='0'
##### Configuring dhcp server... #####
Open config: '/etc/config/dhcp'.
Read config: '/etc/config/dhcp'...
time = 720
time = 60
time = 43200
Start IP: 192.168.1.10, count: 50
Close config: '/etc/config/dhcp'.
Open config: '/etc/ethers'.
Read config: '/etc/ethers'...
Close config: '/etc/ethers'...
- init -
Bummer, cannot run
Please press Enter to activate this console.
BusyBox v1.4.2 (2015-05-19 08:31:19 NOVT) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
M I N D S P E E D Technologies - Build v6.0 for Comcerto
_____ _ _____ _____ __ __
| ___| | | |_ _| | ___| \ \/ /
| ___| | |__ | | | ___|
|_____| |____| |_| |_____| /_/\_\
TAU-4/8.IP software is based on OpenWRT
---------------------------------------------------
root@(none):~#
