Проблема с загрузкой МХА-32

[Батор]

Здравствуйте. Мха-32 не грузится. Выходит вот такой лог загрузки и на этом останавливается
U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Dec 24 2009 - 19:02:52)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x3f3f0c1e
Top of RAM usable for U-Boot at: 84000000
Reserving 449k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
sp=0x83ecbf98 addr=0x83f8c000 => Relocate U-boot

[Кирилл]

Здравствуйте.
Я правильно понимаю, что до запроса остановить загрузку дело даже не доходит?

[Батор]

Да.

[Кирилл]

Данное устройство необходимо отправить нам для ремонта/восстановления.
Локально у вас не получиться ничего с ним сделать.

[Батор]

Здравствуйте! проблема с МХА-32. останавливается загрузка. Обновил ПО.результата не дало.также останавливается.
U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Dec 24 2009 - 19:02:52)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1a1a0c1e
Top of RAM usable for U-Boot at: 84000000
Reserving 449k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
sp=0x83ecbf98 addr=0x83f8c000 => Relocate U-boot
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device MXA, host test1
88e6131: ID 0x141 success!
SFP1 Up
SFP2 Up
IP: 10.100.35.217
Server IP: 10.100.35.220
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Feb 10 2010 02:24:16
***************************************
### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0

Copy 7864320 bytes .............................................................


## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 5985054 Bytes = 5.7 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Comandline = flashboot
Reset FE tx bd index to zero ... Starting kernel at 0x801006d8 ...


LINUX started...
DETECTED system memsize: 67108864 bytes.
2Boot:[2]flashboot
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
Linux version 2.4.20-MVS (root@develop) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.
3-9))
#33 Thu Jan 19 17:31:59 NOVT 2017
Can't analyze prologue code at 8011ec18
Determined physical RAM map:
Initial ramdisk at: 0x8027d000 (5423104 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,57600
trap_init:board_be_init blocked
r4koff 1000000 CPU 200.00 MHz
Console: colour dummy device 80x25
Enable Watchdog driver
0.81 BogoMIPS
MIPS CPU counter frequency is fixed at 100000000 Hz
Memory: 56816k/57536k available (1316k kernel code, 720k reserved, 5400k data, 8
4k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware on host bus 0.Ignored
Initialize Diplomat-IP Fast Ethernet device.
Request IO region for FE Ethernet device, name=eth0.
eth0: TXC-FE ether at 0x280, using assigned IRQ 6
WARNING: A multicast kernel is in use.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
initialize_kbd: Keyboard failed self test
malta_int.c:the irq 1 is invalid
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SEl
RIAL_PCI
SERIAL_Diplomat-IP enabled
ttyS00 at 0x03f8 (irq = 3) is a ST16654
RAMDISK driver initialized: 1 RAM disks of 25000K size 1024 blocksize
loop: loaded (max 8 devices)
pld: version mxa32_v7.c Jan 19 2017 17:32:09
pld: image 78422 bytes, reset nCONFIG... ok, set nCONFIG... ok
loading: ....................OK
board_driver: ok!
init spi(twi) devices:
at26_driver: ok!
at26df321 device
mv6131_driver: ok!
data_driver: ok!
ibuf_driver: ok!
physmap flash device: 2000000 at 1fc00000
gl256: Found 1 x16 devices at 0x0 in 16-bit mode
num 1 mrf 1 id 227e
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Enabling fast programming.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cryptoapi: loaded
cryptoapi: Registered md5 (0)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 5296k freed
cnanda: make device for BOOT DISK.
cnanda: mount root file system...
VFS: Mounted root (ext2 filesystem).
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.7.2 (2010-04-16 10:13:30 MDT)
enter minte module
apply network from user config
ifconfig: eth0 mac 10:11:12:40:02:40 ip 10.100.5.136
netmask 255.255.255.192 gw 10.100.10.1 up
FE: busy!
vconfig : eth0.10 up
eth0.10: add 01:00:5e:00:00:01 mcast address to master interface
route: SIOCADDRT: Network is unreachable
apply configs name from user config
>> loading firmware
tftp: sendto: Network is unreachable
>> decompress binary
>> copy security
>> copy device config
syslogd: msg to /var/log/messages
*** Webs.Start ***
defIface unknown value, set to 'eth0'
Get ip Faild
no network found
*** Webs.Ready ***
wlog: start [32]

>> Soft: Jan 19 2017 17:29:34

HAL: Init [0] success
Malloc addr 0xa2080000 for dma 1.
Malloc addr 0x101caab0 for packet.
>> TXC started ...
Number of DSL ports: 32
DHCP & PPPoE Access-Node ID: New-Zarya/10:11:12:40:02:40
>> Starting PPPoE intermediate agent ...
>> Starting L2 DHCP relay agent ...
>> cpe igmp task enabled
>> uplink igmp task enabled
>> access port counters poll task enabled
Maxtane Release: GS_CMX_445
Compiled for: MAX_NUM_LBUSES=2, MAX_NUM_CHIPS=4, MAX_NUM_CHIPS_PER_LBUS=2
Task Name : tExStartSys Priority: 90 taskId 1
Task Name : tExtEvent Priority: 90 taskId 2

INFO:--------------------[ Start Diagnostics ]--------------------
INFO: Pre-Init IO Driver Diagnostics Completed.

INFO:--------------------[ Start Initialization ]--------------------
INFO:--------------------[ System Initialized ]-------------------
Task Name : tExTimeReference Priority: 90 taskId 3
Task Name : tExSnmp Priority: 130 taskId 4


@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
ethaddr=10:11:12:40:2:40
preboot=
ethact=
fwchange1=tftp 80a00000 $(kernfile);erase bfc60000 c03dffff;cp.b 80a00000 bfc600
00 780000
fwchange2=tftp 80a00000 $(kernfile);erase c0420000 c0b9ffff;cp.b 80a00000 c04200
00 780000
ubchange=tftp 80a00000 u-boot.bin;protect off bfc00000 bfc3ffff;erase bfc00000 b
fc3ffff;cp.b 80a00000 bfc00000 34000
altbootcmd=cp.b c0420000 80a00000 780000;bootm 80a00000
devivemodel=mxa32
loadfw=yes
krnload=cp.b bfc60000 80a00000 780000
kernfile=uImage32
hostname=test1
sysname=MXA
devicemodel=mxa32
bootcmd=run krnload;bootm 80a00000
ipaddr=10.100.35.217
netmask=255.255.255.192
gatewayip=10.100.35.193
serverip=10.100.35.220
netretry=no

Environment size: 739/131068 bytes
@>

[Кирилл]

Здравствуйте.
Выполните

set devivemodel
set nfsboot
set loadfw no
save
reset

После запуска устройства, кроме наблюдений в консоль проверьте есть ли пинг до устройства, возможно ли подключение через telnet.

[Батор]

Здравствуйте! МХА-32 загрузка останавливается .Появляется сообщение

167: SIGUSR1


@>print
nfsboot=tftp 0x80a00000 uImage;bootm 0x80a00000
bootdelay=5
baudrate=57600
preboot=
ethact=
ubunprot=protect off bfc00000 bfc3ffff
fwchange1=tftp 80a00000 $(kernfile);erase bfc60000 c03dffff;cp.b 80a00000 bfc600
00 780000
fwchange2=tftp 80a00000 $(kernfile);erase c0420000 c0b9ffff;cp.b 80a00000 c04200
00 780000
ubchange=tftp 80a00000 u-boot.bin;protect off bfc00000 bfc3ffff;erase bfc00000 b
fc3ffff;cp.b 80a00000 bfc00000 34000
altbootcmd=cp.b c0420000 80a00000 780000;bootm 80a00000
bootcmd=run krnload;bootm 80a00000
devicemodel=mxa32
sysname=MXA
ethaddr=A8:F9:4B:81:71:4d
gateweyip=10.131.19.161
netmask=255.255.255.224
vlan=10
gatewayip=10.131.38.33
serverip=172.16.25.9
krnload=cp.b bfc60000 80a00000 780000
kernfile=uImage32
loadfw=no
ipaddr=10.131.38.61
hostname=Krasnyi_Yar
netretry=no

Environment size: 794/131068 bytes
@>

[Кирилл]

Здравствуйте, приложите полный лог загрузки.

[Батор]

U-Boot 1.1.3 ( R.1.0.0 Diplomat_IP-E2 @ Dec 24 2009 - 19:02:52)

UP DRAM Total Size: 128MB
DN DRAM Total Size: 128MB
DRAM Used By CPU: 64MB
DDR tune delay: 0x1b1b0c22
Top of RAM usable for U-Boot at: 84000000
Reserving 449k for U-Boot at: 83f8c000
Reserving 640k for malloc() at: 83eec000
Reserving 44 Bytes for Board Info at: 83eebfd4
Reserving 36 Bytes for Global Data at: 83eebfb0
Reserving 128k for boot params() at: 83ecbfb0
sp=0x83ecbf98 addr=0x83f8c000 => Relocate U-boot
Vend. 0x1, Type 0x227e
AMD_29GL256N flash
In: serial
Out: serial
Err: serial
Net:
device MXA, host Krasnyi_Yar
88e6131: ID 0x141 success!
SFP1 Up
SFP2 Up
IP: 10.131.38.61
Server IP: 172.16.25.9
Copyright (C) 2008, All Rights Reserved
Version 1.0.0 Feb 10 2010 02:24:16
***************************************
### main_loop: bootcmd="run krnload;bootm 80a00000"
Hit any key to stop autoboot: 0

Copy 7864320 bytes .............................................................


## Booting image at 80a00000 ...
Image Name: MIPS Linux-2.4.20 DipIP E2
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 6292978 Bytes = 6 MB
Load Address: 80100000
Entry Point: 801006d8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Comandline = flashboot
Reset FE tx bd index to zero ... Starting kernel at 0x801006d8 ...


LINUX started...
DETECTED system memsize: 67108864 bytes.
2Boot:[2]flashboot
Primary instruction cache 8kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
Linux version 2.4.20-MVS (root@develop) (gcc version 3.3.3 (DENX ELDK 3.1.1 3.3.
3-9))
#28 Fri Jan 31 09:29:12 NOVT 2014
Can't analyze prologue code at 8011ec18
Determined physical RAM map:
Initial ramdisk at: 0x8027d000 (5730304 bytes)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,57600
trap_init:board_be_init blocked
r4koff 1000000 CPU 200.00 MHz
Console: colour dummy device 80x25
Enable Watchdog driver
0.81 BogoMIPS
MIPS CPU counter frequency is fixed at 100000000 Hz
Memory: 56516k/57236k available (1316k kernel code, 720k reserved, 5700k data, 8
4k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware on host bus 0.Ignored
Initialize Diplomat-IP Fast Ethernet device.
Request IO region for FE Ethernet device, name=eth0.
eth0: TXC-FE ether at 0x280, using assigned IRQ 6
WARNING: A multicast kernel is in use.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
LSP Revision 1
Starting kswapd
Disabling the Out Of Memory Killer
initialize_kbd: Keyboard failed self test
malta_int.c:the irq 1 is invalid
lSerial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI S
ERIAL_Diplomat-IP enabled
ttyS00 at 0x03f8 (irq = 3) is a ST16654
RAMDISK driver initialized: 1 RAM disks of 25000K size 1024 blocksize
loop: loaded (max 8 devices)
pld: version mxa32_v7.c Jan 31 2014 09:29:22
pld: image 78422 bytes, reset nCONFIG... ok, set nCONFIG... ok
loading: ....................OK
board_driver: ok!
init spi(twi) devices:
at26_driver: ok!
at26df321 device
mv6131_driver: ok!
data_driver: ok!
ibuf_driver: ok!
physmap flash device: 2000000 at 1fc00000
gl256: Found 1 x16 devices at 0x0 in 16-bit mode
num 1 mrf 1 id 227e
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
Enabling fast programming.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cryptoapi: loaded
cryptoapi: Registered md5 (0)
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 5596k freed
cnanda: make device for BOOT DISK.
cnanda: mount root file system...
VFS: Mounted root (ext2 filesystem).
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 84k freed
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.7.2 (2010-04-16 10:13:30 MDT)
enter minte module
apply network from user config
ifconfig: eth0 mac a8:f9:4b:81:71:4d ip 10.131.38.61
netmask 255.255.255.224 gw 10.131.38.33 up
vconfig : eth0.10 up
eth0.10: add 01:00:5e:00:00:01 mcast address to master interface
apply configs name from user config
>> decompress binary
>> copy security
>> copy device config
syslogd: msg to /var/log/messages
*** Webs.Start ***
defIface unknown value, set to 'eth0'
Get ip Faild
no network found
*** Webs.Ready ***
wlog: start [32]

>> Soft: Jan 31 2014 09:27:08

HAL: Init [0] success
Malloc addr 0xa2280000 for dma 1.
Malloc addr 0x101be520 for packet.
>> TXC started ...
Number of DSL ports: 32
DHCP & PPPoE Access-Node ID: Krasnyi_Yar/a8:f9:4b:81:71:4d
>> Starting PPPoE intermediate agent ...
>> Starting L2 DHCP relay agent ...
>> cpe igmp task enabled
>> uplink igmp task enabled
Maxtane Release: GS_CMX_445
Compiled for: MAX_NUM_LBUSES=2, MAX_NUM_CHIPS=4, MAX_NUM_CHIPS_PER_LBUS=2
Task Name : tExStartSys Priority: 90 taskId 1
Task Name : tExtEvent Priority: 90 taskId 2

INFO:--------------------[ Start Diagnostics ]--------------------
INFO: Pre-Init IO Driver Diagnostics Completed.

INFO:--------------------[ Start Initialization ]--------------------
INFO:--------------------[ System Initialized ]-------------------
Task Name : tExTimeReference Priority: 90 taskId 3
Task Name : tExSnmp Priority: 130 taskId 4
167: SIGUSR1

[Кирилл]

Проходит ли пинговка на МХА, доступен ли по telnet?

[Батор]

пинги не проходят. телнет не доступен

[Кирилл]

Батор, отправляйте в ремонт. Удаленно невозможно диагностировать возможную причину сбоя. А ввиду отсутствия доступа к устройству, что-то попробовать не представляется возможным.

[Батор]

удаленный доступ проблему не решит? т.е проблема аппаратная?

[Кирилл]

Скорее всего да. дело в том, что по удаленке я смогу войти только в загрузчик и выполнить минимальный набор действия, если быть точным, то только выполнить запись ПО. Но я не думаю, что это даст результат.

[Батор]

Здравствуйте! мха-32 останавливается загрузка. Светодиод Status гаснет.В чем может быть проблема?