Есть такой стенд
Пк1 - ip=1.1.1.254
Микротик RB951Ui, 1 порт ip=1.1.1.1, 2 порт ip 3.3.3.1
Eltex MES2324B 1 порт ip=3.3.3.2 2 порт 2.2.2.1
Пк2 ip = 2.2.2.254
Пытаюсь настроить между ними по ospf связь. (настройки минимум для начала)
Микротик видит eltex, и пингует ПК2.
А eltex не видит ПК1, пинг не идет.
Конфигурация микротика
by RouterOS 6.28# software id = 9VY4-H77R
#
/interface bridge
add admin-mac=4C:5E:0C:66:44:49 auto-mac=no name=bridge-local
add name=loopback
/interface ethernet
set [ find default-name=ether1 ] name=ether1-gateway
set [ find default-name=ether2 ] name=ether2-master-local
set [ find default-name=ether3 ] master-port=ether2-master-local name=\ ether3-slave-local
set [ find default-name=ether4 ] master-port=ether2-master-local name=\ ether4-slave-local
set [ find default-name=ether5 ] master-port=ether2-master-local name=\ ether5-slave-local
/interface wireless
set [ find default-name=wlan1 ] band=2ghz-b/g/n disabled=no distance=indoors \ frequency=auto l2mtu=1600 mode=ap-bridge ssid=MikroTik-66444D \ wireless-protocol=802.11
/ip neighbor discovery
set ether1-gateway discover=no
/ip pool
add name=dhcp ranges=1.1.1.2-1.1.1.254
/ip dhcp-server
add address-pool=dhcp disabled=no interface=bridge-local name=default
/routing ospf instance
set [ find default=yes ] redistribute-connected=as-type-1 router-id=\ 10.255.255.2
/interface bridge port
add bridge=bridge-local interface=ether2-master-local
add bridge=bridge-local interface=wlan1
/ip address
add address=1.1.1.1/24 comment="default configuration" interface=\ ether2-master-local network=1.1.1.0
add address=10.255.255.2/24 interface=loopback network=10.255.255.2
add address=3.3.3.1/22 interface=ether1-gateway network=3.3.0.0
/ip dhcp-client
add comment="default configuration" dhcp-options=hostname,clientid interface=\ ether1-gateway
/ip dhcp-server network
add address=1.1.1.0/24 gateway=1.1.1.1 netmask=24
/ip dns
set allow-remote-requests=yes
/ip dns static
add address=1.1.1.1 name=router
/ip firewall nat
add action=masquerade chain=srcnat comment="default configuration" \ out-interface=ether1-gateway
/ip route
add distance=1 gateway=3.3.3.2
/ip upnp
set enabled=yes
/ip upnp interfaces
add interface=bridge-local type=internal
add interface=ether1-gateway type=external
/romon port
add disabled=no
/routing ospf network
add area=backbone network=3.3.3.0/24
add area=backbone network=1.1.1.0/24
/system leds
set 5 interface=wlan1
/tool mac-server
set [ find default=yes ] disabled=yes
add interface=ether2-master-local
add interface=ether3-slave-local
add interface=ether4-slave-local
add interface=ether5-slave-local
add interface=wlan1
add interface=bridge-local
/tool mac-server mac-winbox
set [ find default=yes ] disabled=yes
add interface=ether2-master-local
add interface=ether3-slave-local
add interface=ether4-slave-local
add interface=ether5-slave-local
add interface=wlan1
add interface=bridge-local
eltex настраивал по такому мануалу
Настройка для версии 4.0.x
1) Создаем interface vlan для создания соседства
console(config)#interface vlan 10
console(config-if)#ip address 10.10.10.5 255.255.255.252
console(config-if)#exit
2) Настройки в режиме глобальной конфигурации
console(config)#router ospf 1
console(router_ospf_process)#network 10.10.10.5 area 4.4.4.4
console(router_ospf_process)#router-id 5.5.5.5
console(router_ospf_process)#exit
Контроль работы протокола
Просмотр ospf соседей - sh ip ospf neighbor
Просмотр таблицы LSDB - show ip ospf database
Просмотр состяния ospf - sh ip ospf
1. пункт не брал - разобраться хотя бы без влана на элтексе.
Понятное дело, что ip будут свои (3.3.3.2 и 2.2.2.1), area-зону брал 0.0.0.0, router-id=10.255.255.3
Просмотр соседей ничего не дал.
Но как тогда микротик видит ПК2 и я даже могу на него зайти.
Где в eltex я что-то не так настроил?