LTP8X+NTP-2+Cisco2950 multicast c тегом qinq

[terran]

Добрый день!
Имеется следующая топология:
LTP8X+NTP-2+Cisco2950. Cisco2950 на access подключены абоненты, получают интернет через PPPoE пытаются смотреть IPTV.
На LTP8X приходит 2 vlana - 1 и 701: 1 управление, 701 инет+iptv. Все это добро тагом валится на NTP-2. NTP-2 передает оба vlana на транковый порт кошки. Управление на свитче присутствует и абоненты живут в сваем vlane с интернетом все ок. Проблема в следующем, при запуске iptv, мультикастовый трафик с NTP-2 на порт кошки прилетает с тегом QinQ Вопрос почему?) QinQ НИГДЕ не используется!!!
Ниже конфигурации.
Профили на LTP8X
LTP8X(pon/profiles_ont/multicast-2)> show
Name: 'iptv'
Description: 'iptv'
Multicast enabled: true
Dedicated igmp datapath: false
Service: 1
Membership service [0]: false
Membership service [1]: true
Membership service [2]: false
Membership service [3]: false
Membership service [4]: false
Membership service [5]: false
Membership service [6]: false
Vlan id: 701
Vlan pr: 0
LTP8X(pon/profiles_ont/services-2)> show
Name: 'test-l2switch'
Description: 'test-l2switch'
Encryption: false
Downstream broadcast: true
Service [0]:
Enabled: true
Q in q: false
Inner vid: 1
Outer vid: 1
Mac table entry limit: unlimited
Service [1]:
Enabled: true
Q in q: false
Inner vid: 1
Outer vid: 701
Mac table entry limit: unlimited
Service [2]:
NTP-2
Профиля в acs нету так что копипаст из web морды.
GPON Interface:
veip0/veip0 VlanMuxMode
veip1/veip1 VlanMuxMode
veip4/veip4 VlanMuxMode
WAN Services:
Interface Description Type Vlan8021p VlanMuxId Igmp NAT Firewall
veip0.1 vlan.1 Bridge 0 1 Disabled Disabled Disabled
veip1.1 vlan.701 Bridge 0 701 Disabled Disabled Disabled
veip4.1 ipoe_veip4 IPoE 0 1101 Disabled Disabled Disabled
VLAN Settings:
Select a LAN port: 1
Enable VLAN Mode
vlna 701
Interface Grouping:
Default
users_vlan701 veip1.1 eth1.701
management_vlan1 veip0.1 eth1.0
Multicast:
все по default
Allowed Groups Remove
239.195.0.0 - 239.195.255.255
Подскажите в какую позу поставить LTP8X что бы убрать qinq тагирование трафика.
Заранее Спасибо!

[vadim_kowalev]

Здравствуйте! Пришлите, пожалуйста, вывод команды pon --> ont_sn серийник --> show config с данной NTP-2.

[terran]

Профиль в ACS для ONT на 2 vlana и 2 тагированных порта eth0,eth1

"InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.DHCPServerEnable" "FALSE"
"InternetGatewayDevice.LANDevice.2.LANEthernetInterfaceConfig.1.X_BROADCOM_COM_VLAN_Enable" "1"
"InternetGatewayDevice.LANDevice.2.LANEthernetInterfaceConfig.1.X_BROADCOM_COM_VLAN_TagList" "701/0"
"InternetGatewayDevice.LANDevice.2.LANEthernetInterfaceConfig.2.X_BROADCOM_COM_VLAN_Enable" "1"
"InternetGatewayDevice.LANDevice.2.LANEthernetInterfaceConfig.2.X_BROADCOM_COM_VLAN_TagList" "701/0"
"InternetGatewayDevice.LANDevice.2.LANHostConfigManagement.DHCPServerConfigurable" "0"
"InternetGatewayDevice.LANDevice.2.LANHostConfigManagement.DHCPServerEnable" "FALSE"
"InternetGatewayDevice.LANDevice.2.X_BROADCOM_COM_IgmpSnoopingConfig.Enable" "TRUE"
"InternetGatewayDevice.LANDevice.2.X_BROADCOM_COM_IgmpSnoopingConfig.Mode" "Standard"
"InternetGatewayDevice.LANDevice.3.LANHostConfigManagement.DHCPServerConfigurable" "0"
"InternetGatewayDevice.LANDevice.3.LANHostConfigManagement.DHCPServerEnable" "FALSE"
"InternetGatewayDevice.LANDevice.3.X_BROADCOM_COM_IgmpSnoopingConfig.Enable" "TRUE"
"InternetGatewayDevice.LANDevice.3.X_BROADCOM_COM_IgmpSnoopingConfig.Mode" "Standard"
"InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeEnable" "TRUE”"
"InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeName" "Default"
"InternetGatewayDevice.Layer2Bridging.Bridge.2.BridgeEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Bridge.2.BridgeName" "management_vlan1"
"InternetGatewayDevice.Layer2Bridging.Bridge.3.BridgeEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Bridge.3.BridgeName" "users_vlan701"
"InternetGatewayDevice.Layer2Bridging.Filter.1.FilterBridgeReference" "1"
"InternetGatewayDevice.Layer2Bridging.Filter.1.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.1.FilterInterfaceName" "eth0"
"InternetGatewayDevice.Layer2Bridging.Filter.2.FilterBridgeReference" "1"
"InternetGatewayDevice.Layer2Bridging.Filter.2.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.2.FilterInterfaceName" "eth1"
"InternetGatewayDevice.Layer2Bridging.Filter.3.FilterBridgeReference" "2"
"InternetGatewayDevice.Layer2Bridging.Filter.3.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.3.FilterInterfaceName" "eth0.701"
"InternetGatewayDevice.Layer2Bridging.Filter.3.X_BROADCOM_COM_VLANIDFilter" "701"
"InternetGatewayDevice.Layer2Bridging.Filter.4.FilterBridgeReference" "2"
"InternetGatewayDevice.Layer2Bridging.Filter.4.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.4.FilterInterfaceName" "eth1.701"
"InternetGatewayDevice.Layer2Bridging.Filter.4.X_BROADCOM_COM_VLANIDFilter" "701"
"InternetGatewayDevice.Layer2Bridging.Filter.5.FilterBridgeReference" "0"
"InternetGatewayDevice.Layer2Bridging.Filter.5.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.5.FilterInterfaceName" "veip4.1"
"InternetGatewayDevice.Layer2Bridging.Filter.6.FilterBridgeReference" "1"
"InternetGatewayDevice.Layer2Bridging.Filter.6.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.6.FilterInterfaceName" "veip0.1"
"InternetGatewayDevice.Layer2Bridging.Filter.7.FilterBridgeReference" "2"
"InternetGatewayDevice.Layer2Bridging.Filter.7.FilterEnable" "TRUE"
"InternetGatewayDevice.Layer2Bridging.Filter.7.FilterInterfaceName" "veip1.1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.ConnectionType" "IP_Bridged"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.Enable" "TRUE"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.Name" "vlan.1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_ConnectionId" "1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_IfName" "veip0.1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_VlanMux8021p" "0"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_VlanMuxID" "1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.ConnectionType" "IP_Bridged"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.Enable" "TRUE"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.Name" "vlan.701"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_ConnectionId" "1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_IfName" "veip1.1"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_VlanMux8021p" "0"
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_VlanMuxID" "701"
"InternetGatewayDevice.X_BROADCOM_COM_AppCfg.DnsProxyCfg.Enable" "FALSE"
"InternetGatewayDevice.X_BROADCOM_COM_AppCfg.UpnpCfg.Enable" "FALSE"
"InternetGatewayDevice.X_BROADCOM_COM_EthernetSwitch.EnableVirtualPorts" "TRUE"
"InternetGatewayDevice.X_BROADCOM_COM_IGMPCfg.AvailableGroupsEntity.1.DestinationIPEnd" "239.195.255.255"
"InternetGatewayDevice.X_BROADCOM_COM_IGMPCfg.AvailableGroupsEntity.1.DestinationIPStart" "239.195.0.0"
"InternetGatewayDevice.X_BROADCOM_COM_IGMPCfg.IgmpVer" "2"
"InternetGatewayDevice.X_BROADCOM_COM_McastCfg.McastPrecedence" "-1"
"InternetGatewayDevice.X_BROADCOM_COM_PwrMngtCfg.CPUr4kWaitEn" "FALSE"
"InternetGatewayDevice.X_BROADCOM_COM_PwrMngtCfg.DRAMSelfRefreshEn" "FALSE"
"InternetGatewayDevice.X_BROADCOM_COM_PwrMngtCfg.EthAutoPwrDwnEn" "FALSE"
"InternetGatewayDevice.X_BROADCOM_COM_PwrMngtCfg.EthEEE" "FALSE"

[terran]

up

[terran]

up

[vadim_kowalev]

Здравствуйте! Некоторые параметры приведенного Вами acs профиля весьма необычны. Не могу сказать точно, как они влияют на прохождение пакетов.
Попробуйте загрузить на NTP-2 acs профиль, который приведен ниже

set property "InternetGatewayDevice.X_BROADCOM_COM_EthernetSwitch.EnableVirtualPorts" "TRUE"
set property "InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Bridge.1.BridgeName" "ALL_Services" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.1.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.1.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.1.FilterInterfaceName" "eth0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.2.FilterInterfaceName" "eth1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=veip4.1%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=veip4.1%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=veip0.1%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=veip0.1%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=veip1.1%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=veip1.1%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.DHCPServerEnable" "FALSE" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.Enable" "TRUE" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1.IPInterfaceIPAddress" "192.168.1.1" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.%X_BROADCOM_COM_IfName=eth0%.X_BROADCOM_COM_VLAN_Enable" "1" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.%X_BROADCOM_COM_IfName=eth0%.X_BROADCOM_COM_VLAN_TagList" "1/0, 701/0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.1%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.1%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.1%.FilterInterfaceName" "eth0.1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.1%.SourceMACFromVendorClassIDFilterExclude" "1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.1%.X_BROADCOM_COM_VLANIDFilter" "1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.701%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.701%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.701%.FilterInterfaceName" "eth0.701" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.701%.SourceMACFromVendorClassIDFilterExclude" "1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth0.701%.X_BROADCOM_COM_VLANIDFilter" "701" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.%X_BROADCOM_COM_IfName=eth1%.X_BROADCOM_COM_VLAN_Enable" "1" nocheck
set property "InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.%X_BROADCOM_COM_IfName=eth1%.X_BROADCOM_COM_VLAN_TagList" "1/0, 701/0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.1%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.1%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.1%.FilterInterfaceName" "eth1.1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.1%.SourceMACFromVendorClassIDFilterExclude" "1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.1%.X_BROADCOM_COM_VLANIDFilter" "1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.701%.FilterBridgeReference" "0" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.701%.FilterEnable" "TRUE" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.701%.FilterInterfaceName" "eth1.701" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.701%.SourceMACFromVendorClassIDFilterExclude" "1" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.%+FilterInterfaceName=eth1.701%.X_BROADCOM_COM_VLANIDFilter" "701" nocheck
set property "InternetGatewayDevice.WANDevice.5.X_BROADCOM_COM_WANPonInterfaceConfig.Enable" "TRUE" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.Enable" "TRUE" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.ConnectionType" "IP_Bridged" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.Name" "Service_1" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_IfName" "veip0.1" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_ConnectionId" "1" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_VlanMux8021p" "0" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.1.WANIPConnection.1.X_BROADCOM_COM_VlanMuxID" "1" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.Enable" "TRUE" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.ConnectionType" "IP_Bridged" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.Name" "Service_2" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_IfName" "veip1.1" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_ConnectionId" "1" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_VlanMux8021p" "0" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.2.WANIPConnection.1.X_BROADCOM_COM_VlanMuxID" "701" nocheck
set property "InternetGatewayDevice.Layer2Bridging.Filter.-2.Ena" "0" nocheck
set property "InternetGatewayDevice.WANDevice.-2.Ena" "0" nocheck
set property "InternetGatewayDevice.WANDevice.5.WANConnectionDevice.-2.Ena" "0" nocheck

[terran]

Здравствуйте! Попробуем. Я так пологая все через один бридж. Ну а профили приходится создавать по мануалам которые скачены с вашего сайта, анализу xml конфига ONT и по древу параметров TR069 с web сервера ACS. Был бы подробный man с описанием всех команд TR069 для ONT было бы попроще. Подскажите а последние три команды что делают? Профиль в web ACS их не переваривает.
"InternetGatewayDevice.Layer2Bridging.Filter.-2.Ena" "0" nocheck
"InternetGatewayDevice.WANDevice.-2.Ena" "0" nocheck
"InternetGatewayDevice.WANDevice.5.WANConnectionDevice.-2.Ena" "0" nocheck

[terran]

Здравствуйте!
Немного затянул, не было времени проверить ваш профиль. Попробовал, не работает(((. Трафик со свитча не ходит. На OLT видны маки тока самого свитча, притом в как в первом влане так и во втором. Все же почему multicast трафик тагируется q-in-q? Этот тег летит точно с OLT, ведь на ONT стандартный BusyBox, а на linux q-in-q работает только с волшебным пенделем.
Спасибо за помощь!

[alexmasz]

Добрый день!

Будет ли работать схема терминал LTP-4X:
front-port 0 - uplink trunk mode(tagged vlan 10,11,12,13,40) --> mes3124f
front-port 1 - uplink(резерв) --> какая-то сеть --> mes3124f

Можно ли завернуть мои вланы(10,11,12,13,40) в svlan и отправить во front-port 1 для передачи на mes3124f через чужую сеть?

Спасибо!