Lte-2x недоступен по локальному ипу.

[VladimirK]

Здравствуйте, проблема в следующем, после перезагрузки из-за откл-я питания, lte-2x отключился, прдключился к нему консолью, сбросил все настройки, но он недоступен по дефолтному ипу, и при выполнении команд выдает следующие ошибки
LTE-8X# switch
telnet: can't connect to remote host (127.0.0.1): Connection refused
LTE-8X# save
ERROR: Can't save configuration

В общем есть подозрение, что проблема из-за неверной прошивки, которая применилась из-за перезагрузки, т.к.
LTE-8X# show version
Eltex LTE software version 3.14.2 build 938 on 08.04.2014 14:00:51

LTE-8X# show factory settings
Factory settings
Device type: LTE-2X
Hardware revision: 1v2
Serial number: TG1A000050
Mac: A8:F9:4B:80:4E:8F

Вопрос, как можно накатить нормальную прошивку, если проблема конечно в этом.
Спасибо.

[vadim_kowalev]

Здравствуйте! для LTE-8X это верная версия ПО. Можете сказать, какая версия ПО у Вас стояла до этого?
Не дает перейти только на switch или OLT чипы тоже не отвечают? Лог можете вывести, log show ?
Есть ли возможность подключиться к LTE консольным кабелем, перезагрузить её и снять лог загрузки?

[VladimirK]

Добрый день.
По верная, но железка то lte-2x, если верить выводу команды show device.
Логи
LTE-8X# log show
Jan 1 06:00:06 LTE-8X sshd: Server listening on 0.0.0.0 port 22.
Jan 1 06:00:06 LTE-8X config: Socket file = /tmp/config.sock
Jan 1 06:00:06 LTE-8X config: Config path = /etc/config/pon
Jan 1 06:00:07 LTE-8X snmpd: Socket file = /tmp/snmp.sock
Jan 1 06:00:07 LTE-8X snmpd: Config path = /etc/config/pon
Jan 1 06:00:07 LTE-8X snmpd: Call to load_aliases
Jan 1 06:00:08 LTE-8X config: peer: connect: Ok
Jan 1 06:00:08 LTE-8X snmpd: peer: connect: Ok
Jan 1 06:00:08 LTE-8X switchd: Device[0] ID 0xDD7411AB revision 3
Jan 1 06:00:08 LTE-8X switchd: >> cpssDxChNetIfInit2 (devNum=0)
Jan 1 06:00:08 LTE-8X switchd: << cpssDxChNetIfInit2
Jan 1 06:00:08 LTE-8X switchd: init_ports_state()
Jan 1 06:00:08 LTE-8X switchd: init_ports_state() end
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX_ALL_EXCEPT2
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX_MGMT = 3
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX_PON = 4
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX_SLOT_FRONT5
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf6
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf7
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf8
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf9
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf0
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf1
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf2
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf3
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf4
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf5
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf6
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf7
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf8
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf9
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf0
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf1
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf2
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf3
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf4
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf5
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf6
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf7
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf8
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf9
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf0
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf1
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf2
Jan 1 06:00:08 LTE-8X switchd: %ISOLATE: SWITCH_ISOLATION_PORT_VIDX for interf3
Jan 1 06:00:09 LTE-8X switchd: config_stack_add_unit: adding unit 0 to shelf 0
Jan 1 06:00:09 LTE-8X switchd: %VLAN: set VLAN 1 members:
Jan 1 06:00:09 LTE-8X switchd: config_stack_add_unit: adding unit 0 to shelf 0
Jan 1 06:00:09 LTE-8X switchd: %LINK-ENABLE: port front-port 0 disabled
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 0: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 1: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 2: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 3: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 4: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 5: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 6: link up, speed 1
Jan 1 06:00:09 LTE-8X switchd: %LINK-UPDOWN: Port pon-port 7: link up, speed 1
Jan 1 06:00:11 LTE-8X webs: webs: Listening for HTTP requests at address 127.0
Jan 1 06:00:12 LTE-8X chip-proxy: kernlink: connected to kernel
Jan 1 06:00:13 LTE-8X chip-proxy: get config cache success
Jan 1 06:00:25 LTE-8X login: pam_unix(login:session): session opened for user )
Jan 1 06:00:25 LTE-8X login: Accepted password for root from ttyS0
Jan 1 06:00:34 LTE-8X login: pam_unix(login:session): session closed for user t
Jan 1 06:00:40 LTE-8X login: pam_unix(login:session): session opened for user )
Jan 1 06:00:40 LTE-8X login: Accepted password for admin from ttyS0
Jan 1 06:00:42 LTE-8X chip-proxy: wd_cleanup_olts: OLT[0] in CHECKNEWFW state
Jan 1 06:00:43 LTE-8X chip-proxy: wd_cleanup_olts: OLT[1] in CHECKNEWFW state
Jan 1 06:00:43 LTE-8X chip-proxy: wd_cleanup_olts: OLT[2] in CHECKNEWFW state
Jan 1 06:00:43 LTE-8X chip-proxy: wd_cleanup_olts: OLT[3] in CHECKNEWFW state
Jan 1 06:44:49 LTE-8X cli: admin logged out
Jan 1 06:44:49 LTE-8X login: pam_unix(login:session): session closed for user n
Jan 2 00:58:24 LTE-8X login: pam_unix(login:session): session opened for user )
Jan 2 00:58:24 LTE-8X login: Accepted password for admin from ttyS0

Лог загрузки
<0>Restarting system.
Reseting !!

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-98DX4122-48G LE (configured)
** Linux - LE/BE support
** vxWorks(elf) - LE/BE support


U-Boot 1.1.4 (Jul 18 2011 - 09:45:56) Marvell version: 3.4.9.7

U-Boot code: 01200000 -> 0128FFF0 BSS: -> 012A9324

Soc: 88F6281 A0 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 320Mhz , TClock = 166Mhz

DRAM CAS Latency = 5 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM CS[1] base 0x08000000 size 128MB
DRAM Total size 256MB 16bit width
Enabled 4-bytes addressing support for SPI flash
[32768kB@f8000000] Flash: 32 MB
Addresses 27M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (27M - 19M): Done
*** Warning - bad CRC, using default environment


CPU : Marvell Feroceon (Rev 1)
Set ELTEX environment for 2x256 FLASH!

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: Allowed switch ports: 16 17 18 19 20 21 22 23
egiga0 [PRIME], port16, port17, port18, port19, port20, port21, port22, port23
Type "stop" in 3 sec, to stop autoboot
Time out
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................

Un-Protected 1 sectors
## Booting image at f8200000 ...
Image Name: Linux-2.6.22.18
Created: 2014-04-08 6:56:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1252364 Bytes = 1.2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK

Checking for Linux kernel endianess at 0xf8200040 = 0xe1a00000
Linux Kernel is LE

Starting kernel in LE mode ...
Uncompressing Linux.............................................................
Linux version 2.6.22.18 (jenkins@xpon.eltex.loc) (gcc version 3.4.4 (release) (4
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
Machine: Feroceon-KW
DMA memory:
mv_high_memory_paddr 0x0f800000
mv_high_memory_paddr_top 0x10000000
mv_high_memory_vaddr 0xef800000
mv_high_memory_vaddr_top 0xf0000000
Using UBoot passing parameters structure
BoardID from uboot=10
Memory policy: ECC disabled, Data cache writeback
calling iotable_init. MEM_TABLE=
virt=0xef800000, phys=0x0f800000, lengh=0x00800000
virt=0xe0000000, phys=0xe8000000, lengh=0x08000000
virt=0xf1000000, phys=0xf1000000, lengh=0x00100000
virt=0xf8000000, phys=0xf8000000, lengh=0x01000000
virt=0xf4000000, phys=0xf4000000, lengh=0x04000000
virt=0xfb000000, phys=0xfb000000, lengh=0x00010000
virt=0xf2000000, phys=0xf2000000, lengh=0x00010000
Internal prestera id register = 0x000dd743
xCat revision = A1
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 62992
Kernel command line: init=/sbin/save root=/dev/ram0 rw initrd=0x2000000,0x10000)
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 120MB 0MB 0MB = 248MB total
Memory: 232576KB available (2336K code, 213K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....base 08000000, size 128MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base fc000000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base d8000000, size 128MB
SPI_CS ....base f8000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base fb000000, size 64KB
SAGE_UNIT ....base f4000000, size 64MB
DRAGONITE_DTCM ....base f2000000, size 64KB

Marvell Development Board (LSP Version KW_LSP_4.3.0.015)-- DB-98DX4122-48G SE

Detected Tclk 166666667 and SysClk 320000000
Switch default target range: 0F800000..0F800FFF
Switch address window 0: base=00000E00 size=07FF0000
Switch address window 1: base=08000D00 size=07FF0000
Switch default target: UDID=000000D0 UDA=0F800000
Switch decoding windows init is done.
MV Buttons Device Load
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 16384K
RTC has been updated!!!
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
Number of XOR engines to use: 2
MV Buttons Driver Load
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize
Loading Marvell Ethernet Driver:
o Uncached descriptors in DRAM
o DRAM SW cache-coherency
o Multi RX Queue support - 8 RX queues
o Multi TX Queue support - 8 TX Queues
o TCP segmentation offload enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o Rx descripors: q0=64 q1=64 q2=64 q3=64 q4=64 q5=64 q6=64 q7=64
o Tx descripors: q0=532 q1=532 q2=532 q3=532 q4=532 q5=532 q6=532 q7=532
o Loading network interface(s):
o eth0, ifindex = 1, GbE port = 0

Warning: Giga 1 is Powered Off

mvFpRuleDb (c0514000): 2048 entries, 8192 bytes
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
Enabled 4-bytes addressing support for SPI flash (reg IFCONFIG=0x4315)

INFO: sflash_probe - Detected SFlash device 0 (size 33554432)
Base Address : 0xf4000000
Manufacturer ID : 0xc2
Device ID : 0x2019
Sector Size : 0x10000
Sector Number : 512
SPI Serial flash 0 detected @ 0xf4000000, 32768KB (512sec x 64KB)
Enabled 4-bytes addressing support for SPI flash (reg IFCONFIG=0x4315)

INFO: sflash_probe - Detected SFlash device 1 (size 33554432)
Base Address : 0xf4000000
Manufacturer ID : 0xc2
Device ID : 0x2019
Sector Size : 0x10000
Sector Number : 512
SPI Serial flash 1 detected @ 0xf4000000, 32768KB (512sec x 64KB)
6 cmdlinepart partitions found on MTD device spi_flash
Creating 6 MTD partitions on "spi_flash":
0x00000000-0x00200000 : "u-boot"
0x00200000-0x00400000 : "kernel"
0x00400000-0x00800000 : "config"
0x00800000-0x01000000 : "reserved"
0x01000000-0x02000000 : "initrd"
0x02000000-0x04000000 : "data"
Using Hamming 1-bit ECC for NAND device
No NAND device found!!!
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
sdma: loaded
nf_conntrack version 0.5.0 (1984 buckets, 15872 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 120K
restore saved config
uncompressed 69712 bytes from device 0
INIT: version 2.86 booting

running rc.sysinit
chgrp: unknown group utmp
vm.min_free_kbytes = 64
vm.dirty_writeback_centisecs = 200
vm.dirty_expire_centisecs = 400
vm.dirty_background_ratio = 1
vm.dirty_ratio = 2
net.unix.max_dgram_qlen = 2000
kernel.panic_on_oops = 1
kernel.panic = 1
pp_find_all_devices: found 1 PP devices
prestera_init: DMA memory at 0xf801000 (0x200000 bytes)
board: Board control driver_mod5
board: Board ID = 0x06
board: lm75[0] probe read temperature = 26 C
board: lm75[1] probe read temperature = 36 C
board: PLD version = 1
board: PLD write OK
board: pon_reset0 - pld write OK
board: SFP turn on - pld write OK
Sat Jan 1 06:00:05 NOVT 2000
INIT: Entering runlevel: 3
Starting local
Starting iptables

Starting rlogd Starting rlogd
Starting system logger: syslogd
Starting kernel logger: klogd
Starting watchsm
Starting interfaces
Starting OpenBSD Secure Shell server: sshd.
Starting telnetd
Starting crond: crond
Starting ntpclient
Starting pon-host
Starting snmpdaemon



**************************************
* Optical line terminal LTE-8X *
**************************************
LTE-8X login:

[vadim_kowalev]

Скажите, у Вас есть бэкап конфигурации станционного терминала, до возникновения данной проблемы?

[VladimirK]

Бэкапа нет, сорри, за столь долгий ответ не было доступа к интернету.

[VladimirK]

ап